John Soko posted an answer for this Elna Sewing Machines:
"Can be a variety of reasons. Firstly, is it a Quality thread? Cheap thread can be..."
John Soko posted an answer for this Toro Garden:
"21 hours? Isn't it still under warranty? Good luck !"
John Soko posted an answer for this Toro Garden:
"Sounds like you may have stripped the thread in the head when retightening the new plug :(..."
John Soko posted an answer for this Toro Garden:
"Jump onto www.toro.com and download the free service manual for your machine. Note down..."
John Soko posted an answer for this Toro Garden:
"Jump onto www.toro.com and download the free service manual for your machine. Note down..."
John Soko posted an answer for this Toro Power Lawn Mower:
"Take off the wheel not driving - check if the rectangular key is in place, and undamaged."
John Soko posted an answer for this Toro Garden:
"If all else fails, jack up he mower, remove the rear wheels , Take the rectangular shaped..."
John Soko posted an answer for this Toro Garden:
"Jump onto www.toro.com and download the free service manual for your machine. Note down..."
John Soko posted an answer for this Toro Garden:
"Jump onto www.toro.com and download the free service manual for your machine. Note down..."
John Soko posted an answer for this Toro Garden:
"Jump onto www.toro.com and download the free service manual for your machine. Note down..."
John Soko posted an answer for this 1997 Volkswagen Golf:
"Sounds like an issue I had - was the fuel pump (dead)"
John Soko posted an answer for this Bernina Sewing Machines:
"Was it a brand new pedal? May be an idea to test the foot controls on another machine. At..."
John Soko posted an answer for this Bernina Artista 180:
"Does not need to be replaced - have it removed as leaving it in the machine or foot..."
John Soko posted an answer for this Bernina Sewing Machines:
"Innox in a spray can is Magic gear to free up stiff machines. It does not attract grime..."
John Soko posted an answer for this Bernina Bernette Deco 600:
"First thing to do is fit a BRAND NEW needle - ensure it is the correct type AND that it..."
John Soko posted an answer for this Sewing Machines:
"great that it has been solved! My process is - First thing to do is fit a BRAND NEW needle..."
John Soko posted an answer for this Singer Confidence 7469 Mechanical Sewing Machine:
"First thing to do is fit a BRAND NEW needle - ensure it is the correct type AND that it..."
John Soko posted an answer for this Singer 7444 Mechanical Sewing Machine:
"First thing to do is fit a BRAND NEW needle - ensure it is the correct type AND that it..."
John Soko posted an answer for this Brother Sewing Machines:
"First thing to do is fit a BRAND NEW needle - ensure it is the correct type AND that it..."
John Soko posted an answer for this Michley Lil Sew Mechanical Sewing Machine:
"First thing to do is fit a BRAND NEW needle - ensure it is the correct type AND that it..."
John Soko posted an answer for this Sewing Machines:
"First thing to do is fit a BRAND NEW needle - ensure it is the correct type AND that it..."
John Soko posted an answer for this PfaFF Creative 7570:
"First thing to do is fit a BRAND NEW needle - ensure it is the correct type AND that it..."
John Soko posted an answer for this PfaFF Creative 7570:
"At any stage before this started to happen, did you notice a 'bad smell' - electrical?"
John Soko posted an answer for this Singer 3116 Simple:
"Hi, not familiar with this machine, but a few tips - Unthread the machine fully. Remove..."
John Soko posted an answer for this Singer 57815 Mechanical Sewing Machine:
"Unthread the machine fully. Remove the bobbin. Is the bobbin thread the same as the top..."
John Soko posted an answer for this Brother CS6000i Computerized Sewing Machine:
"I hear what you have done .... try this sequence - Unthread the machine fully. Remove the..."
John Soko posted an answer for this Necchi Sewing Machines:
"An easy one to try - put in a new needle in."
John Soko posted an answer for this Singer Sewing Machines:
"Silvia covers it pretty well - heres my take. Unthread the machine fully. Remove the..."