Whirlpool Washing Machines - Page 5 - Recent Questions, Troubleshooting & Support

You can check to see if there is a quick fix by doing the following:

• Verify the power source: Check to see if the dryer is plugged in and if the circuit breaker hasn't tripped. Reset the circuit breaker to see if the dryer comes on if it has been tripped.
• Examine the doorknob: The dryer might not start if the door switch is broken. Open and close the dryer door to check that the door switch is functioning properly. The door switch may need to be replaced if the dryer starts when the door is closed.
• Examine the thermal fuse: If the dryer gets too hot, the thermal fuse, a safety feature, can stop the machine from working. The thermal fuse will need to be replaced if it blows.
• Examine the control panel: The control board may be defective and need to be replaced if none of the aforementioned steps resolve the issue.

The washing machine is not balanced. This might be caused by the washing machine being very packed too tightly or the clothing is not distributed. Or an uneven load.

ck here...... https://www.appliancepartspros.com/repair-help/whirlpool-washer-lxr6232eq0-repair/lxr6232eq0-will-not-stop-filling-with-water.html

Question edited for clarity. Question moved from Computers to Whirlpool Washing Machine. Question translated to English, we only speak English on this North American website! This error code will be displayed if the machine is trying to fill with water but the flow meter doesn't sense any flow for 30 seconds. In this case, check the water supply to be sure you have good pressure for both hot and cold water. Then, consider replacing the flow meter.

Whirlpool F/H - FH No Water Entering Machine or Pressure ...

We had this happen to our Kenmore washer. Your solution might be the same as ours. The reason that the agitation cycle won't start is that the safety switch that senses door closure is out of adjustment or broken. They're hard to get at on our Kenmore, so I just took a short length of fish tank plastic air supply hose and slid it over the probe on the door that pushes the switch open. The added length (try half an inch), was enough to push the safety switch and start the agitation cycle. It's not elegant, but has been a permanent solution for us!

The display screen went bad and has gone bad and should have to be replaced.

Replace faulty shock absorbers and suspension.

If you're finding grease under the washplate of your Whirlpool top load washer, it's likely that the transmission is leaking. The transmission is responsible for turning the drum during the wash cycle, and if it is leaking, it can cause grease to build up under the washplate. Here are a few steps you can take:

1. Check the transmission oil level: The first step is to check the oil level in the transmission. If the oil level is low, it could indicate a leak.
2. Check for leaks: Look for any visible leaks coming from the transmission. If there are leaks, it's best to take it to a qualified repair technician.
3. Clean the washplate and drum: Clean the washplate and drum with warm soapy water and a soft cloth. Be sure to remove any debris or buildup that may have accumulated.
4. Check the transmission oil seal: the oil seal may be the cause of the leak, if it's damaged or worn out, it will need to be replaced by a professional technician.

It's important to keep in mind that the transmission is a complex component, and if you're not comfortable working with it, it's best to consult a professional technician for further diagnosis and repair. It's also important to note that some of these steps require a certain level of mechanical knowledge and experience. If you're not comfortable with checking these items, it's best to consult a professional repair technician if i was able to help my cashapp $ralphpapi thank you have a blessing day

The drive belt cold be faulty and will need to be replaced.

Hello & Welcome to FixYa

This is a common issue with Whirlpool Duet washer however, your whirlpool duet washer needs a reset to resolve the control lock problem. Press and hold the END OF CYCLE /CYCLE SIGNAL button for 15 seconds to reset the control. Please get back to me if you have any other questions.

Kevin

Lots on that error including videos. Stuck Button!

https://www.google.com/search?q=Whirlpool+Cabrio+washer+error+code+F2E1 WHIRLPOOL CABRIO WASHER ERROR F2E1 EXPLAINED https://appliancerepairguides.com > whirlpool-cabrio-w... Mar 31, 2017 - The Cabrio Washer F2E1 error code means there is a stuck key on the user interface board. Unplug the washer for five minutes, plug it back in ... ..

It is is bottom centre it may just be a hose. Do a wash so it leaks, pull it out and tip it back against the wall and look for what it wet.

The drain hose or the filter could be clogged and need to be replaced for your washing machine.

You need to Unscrew the washer pump and search closely inside it, you can watch the following video to find out how to do it by yourself, thank you ??

https://youtu.be/oYL4QqK9LdQ

Platinum WTW8800YW IT IS NOT A CAR MOVED YAH.

have you replaced the hoses? it's a good idea to do that every few years anyway (they get old and often burst) ... some hoses have an inline screen filter that can get stopped up thus your washer would only get hot water if the cold water hose was stopped up.

There are pictures here you can look at https://www.google.com/search?q=whirlpool+washer+LSQ9549L&rlz=1C1QJDB_enCA643CA644&sxsrf=ALiCzsb29DW8EgzmAPhClbqgpqoaaYhn-g:1670563686535&source=lnms&tbm=isch&sa=X&ved=2ahUKEwia7vDY5uv7AhWgmnIEHfHZBDgQ_AUoA3oECAEQBQ&biw=1920&bih=937&dpr=1 ..