Whirlpool duet - Recent Questions, Troubleshooting & Support - Page 3

Hello

Error F31 in your whirlpool duet washer is displayed due to MCU (Motor Control Unit) failure. It is displayed if the heat sink gets too hot and then the MCU stops motor, then MCU sends the signal to CCU (Central control unit). Please check the wire connections between the CCU and MCU, if thats fine then check the motor operation. Hope you understand...replacing the part# that has gone bad is recommended repair. Please get back to me if you have any other questions.

Kevin

Water Temperature Sensor Error - Check the Water Temperature Sensor,Heating Element and Element Relay.
If during the water heating step in wash cycle,the water temperature sensor(NTC) value is out of range,or the heating element circuit has failed,the F05 error code will be displayed - Check connections to
the Sensor,Heating Element and Relay.

Hi

Its a simple procedure to reset the Whirlpool Duet front load. Please press and hold the END OF CYCLE button for 15 seconds to reset. Please get back to me if you have any other questions.

Kevin

f8 is shown when the heater circuit is on with no water in.. it doesnt do it when you unplug the pressure switch because your disabling the heat protect circuit

THE BOARD IS PROBABLY FAULTY

F08 indicates pressure switch stuck on full.



Unplug the appliance from the wall socket.

Take the top off the machine.

Locate the pressure switch, you can identify it by the thin tube attached to it.

Take the tube off, blow down this tube as hard as you can to shift any blockage or restriction in the pressure chamber. Give the pressure switch a couple of good taps with the screwdriver handle.

Refit the tube and try the machine again.

If still doing it, unplug again and follow the tube down.

This end will be attached to the pressure chamber.

Take this chamber off and thoroughly clean it out, clean out the port into the tub too.

Reassemble and try again.



If after this it's still faulty you'll need to start replacing parts.

I'd suggest trying a new pressure switch first.

Failing this, if all of the above fails to resolve the problem you're possibly looking at a faulty main control board.



Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

replace door inter lock

My pant legs and long sleve shirts twist into a knot, every time. How can I stop this from happening?

My washer is leaking what can be the problem

mains filter blown door lock fail main pcd fail appliance doctor

Try holding in the "End of Cycle"tone button

clogged water screens , defective water level pressure switch , clogged drain, kinked drain hose ,. defective water pump , defective water tempeerture switch, damaged water valve solenoid , water inlet valve has an interal malfunction

F28 is a communication error which usually means there is a connection that has come loose. Removing the top and unpplugging and replugging the connectors in will fix 75% of these codes. If the bottom toe panel is not on it will also give you an F28

Unplug or turn the circuit breaker off for 30 seconds.

Reconnect the unit to the power source by turning the breaker back on or plugging the unit back into the wall outlet.

Press the Pause/Cancel/Stop button twice to clear the display.

Start a short cycle to check the operation of the machine by selecting a cycle and pressing and holding the start button until the machine starts if you have any further questions message me back and please remember to rank how this opinion has helped in your appliance situation when our chat has concluded Thanks again Rick

Hello & Welcome to FixYa

Your whirlpool duet washer needs a reset to resolve the control lock problem. Press and hold the END OF CYCLE button for 15 seconds to reset the control. Please get back to me if you have any other questions.

Kevin

Hi, After about year and half Whirlpool duet sport gave F01 error code. The technician manual is located under the lower front panel. There are three possible reasons for F0: 1) EEPROM ERROOR. Unplug a washer for two minutes. Try running it again. (Did not work for me). 2) MAIN RELAYS ERROR. The tech manual suggests replacing CCU. The following is what I did and it fixed the problem, however. Unplug the washer. Remove the top cover by removing the three screws on the back. The CCU unit is in the right bottom corner if standing in front of the washer – it has a lot of wiring. Plug in the unit. While listening to the CCU start any washing cycle. After pressing START you should hear the relay to click. If it clicks twice, within a less than a second, it has a problem. Unplug the washer. Without disconnecting any wires remove the CCU cage from the washer wall. Stand now on the right hand side of the washer in such way that the CCU cage is under your left hand. Pull the right upper corner of the CCU plastic cage (it has a tab) away from you, slide the cage to the right by about an inch, and pull the entire cage away from you. Now knock on the back side of the cage 4-5 times with a bit of force. Install the CCU cage back. Plug in the unit. Try some washing cycle again. If it did not help, repeat the procedure. If it did not work again, see the following. 3) PUMP DRIVE ERROR. The tech manual suggests replacing CCU.

Check the water supply by disconnecting hoses @ the machine & use a bucket to check the flow. If there is a good flow of water,then check the screens inside of the inlet valves for debri.

Cawnee: Thank you for your review. We would like to inquire further about your review with you. Please respond back to this email address, [email protected], with your name, phone number, street address, zip code, model & serial number, and date of purchase on the appliance. We look forward to your reply. Thank you, Maytag® Social Media Relations

Anonymous: Thank you for your review. We would like to inquire further about your review with you. Please respond back to this email address, [email protected], with your name, phone number, street address, zip code, model & serial number, and date of purchase on the appliance. We look forward to your reply. Thank you, Whirlpool® Social Media Relations

Try looking online for another manual. Or call anyone who sells your machine. Me thinks the solution is simple, but you need to talk to any seller of your machine, and soon.

f-ll is too much soap