SWANN Home Security - Recent Questions, Troubleshooting & Support

A flashing green light on a Swann 960H Pro Series security camera system can indicate a few different things, depending on the specific model and configuration of your system. Some possible causes of a flashing green light include:

1. The camera is in setup mode: When a camera is first powered on, it may flash a green light to indicate that it is in setup mode and ready to be configured.
2. The camera is in standby mode: When the camera is not actively recording, it may flash a green light to indicate that it is in standby mode and ready to start recording.
3. The camera is recording: Some models of the Swann 960H Pro Series security camera system have a green light that flashes when the camera is recording.
4. The camera is low on power: Some models of the Swann 960H Pro Series security camera system have a green light that flashes when the camera is low on power.
5. The camera is malfunctioning : Some models of the Swann 960H Pro Series security camera system have a green light that flashes when the camera is malfunctioning.

Video that may help, but that is proprietary information and not generally available. https://www.google.com/search?q=Swann+pro+wiring+diagram+for+camera+circuit+board ..

Try holding the stop or esc button for 10 to 30 sec and let go when you hear a long beep.

This a lengthy procedure, I better refer you to the Swann link where you can find instructions. New Password Reset Procedure

That is proprietary information. Contact Swann direct and tell them what your issue is. https://www.swann.com/downloads/product/906wch_wdc_woy_w2y_w3y_wcx_w2b_instructions_en160209.pdf Or this? https://www.sneakersvip99.top/products.aspx?cname=ir+color+ccd+camera+wiring&cid=62 ..

That means it cannot find a hard disk to store information on.

swann , DVR only they can help you or read your manual , their web site. here they are https://support.swann.com/s/

Swann have great online support direct from the company.

General Idea: On-screen Display (OSD) or Image Control

https://support.swann.com > article Feb 5, 2020 - To access this on your DVR (such as DVR8-5580), you can select a channel ... to avoid losing details due to too much darkness or brightness. Missing: cursor ‎' Must include: cursor

Home - Swann

https://support.swann.com > ... SwannBuddy™ Video Doorbell ... (4480, 4580, 4680, 5580, 5680, 8580, 8780) ... Many of my bullet cameras have lost the IR Illumination over the years., ... ..

Contact Swann to request the diagram.

https://www.youtube.com/watch?v=-XQkIxmHkB0

I would replace all the cables.

Depends what you mean by pairing. The device allows you to view via a Swann app on your 2 mobile phones. So you can watch CCTV video streaming simultaneously on the 2phones or any compatible Android / iPhone device.

a few possibilities: hard drive plug came disconnected somehow hard drive plug/wires are bad hard drive is shot. you may want to try to contact the manufacturer before attempting to open it to find the problem, if your hard drive is bad you will probably need to get the operating system/format programming to load onto a new hard drive. best bet is to find a contact for them and see if they sell replacement parts, my guess is the hard drive is bad. it happens, it sucks, and it can be expensive, the upside is if you are careful and take your time it is usually pretty easy to take the bad one out and put a nwe one in... good luck

1st lets figure out how old your swann cameras are?? If they are within say 5rs old and are digital. Then the answer is YES they should work no problem. After all a digital signal is a digital signal. Unless encrypted of course. Given you have the correct connectors that go from the camera to DVR you should be fine. If not, you can find adapters at any decent electronics store. Kinda like Radio Shack used to be. That is unless you are wireless, then the above "connector" comment is jibberish, and should be ignored. Good luck Mr. Morgan Jason

tncyoo

How bout a please 1st..

Check this link fir that manual. ManualsLib Makes it easy to find manuals online

Sometime your ISP number will change. And you have to look it up. Then insert it in. That should help. Go to Look up my ISP

The answer is with tech support and no in open forums where anyone getting the super password could abuse it. Or call a tech pro in your area.

Check the hard drive. Could be bad or not formatted. Also, try rebooting the system. Could be a defective unit.