Answered Questions & Solved Problems - Page 7
Midea MRS26D5AST Side-by-Side Refrigerator. I have code ep, how to fix please?
Question edited for clarity, full 'make model (what it is)' and correct spelling of make 'Media' to Midea.
Question moved from Cars and Trucks category.
Ice Maker Probe Error
I have a Midea side by side fridge that's about 2 years old.
JustAnswer
https://www.justanswer.com > Appliance Repair
Jul 26, 2023 - The EP error indicates a failure with the temperature sensor or the control board. This would keep the ice maker from activating. Here's the ...
1 answer · Top answer: Greetings and welcome to justanswer, an independent paid question and answer platform. Just ...
Error Codes - Midea MRS26D5AST User Manual [Page 36]
ManualsLib
https://www.manualslib.com > ... > User manual
Midea MRS26D5AST Manual Online: Error Codes. If an error code is displayed on the control panel, contact your place of purchase or Insignia customer service ...
E3, E4, E5, E7, Eb, Ed, EF, EP, EU, F9,Fb, Fd - Midea
midea.es
https://www.midea.es > uploads > 2020/10 > E3-...
PDF
Error code is displayed on main PCB and user interface. 3 Possible causes. ? Temperature sensor or pressure sensor are not connected properly or malfunctioned.
3 pages
https://www.google.com/search?q=Midea+MRS26D5AST+error+code+ep
..
Jeep Commander Rear Brake Pad Installation
Per Chilton Auto repair manual:
Removal & Installation
-
Raise and safely support the vehicle.
-
Remove the rear wheel.
-
Siphon a small amount of brake fluid from the master cylinder reservoir.
-
Insert
a small prybar through the caliper opening and pry the caliper cover
(using the outboard brake pad) to bottom the piston in the caliper bore.
-
Remove the caliper slide bolts.
-
Remove the caliper from the anchor.
WARNING
Support the brake caliper with mechanics wire. Do not let the caliper hang by the brake hose.
-
Remove the brake pads from the caliper.
To install:
-
Install the brake pads onto the caliper.
-
Lubricate the slide pin bolts with grease provided with the brake pads, or suitable silicon grease equivalent.
-
Install the caliper on the anchor and tighten the slide pin bolts to 18 ft. lbs. (25 Nm).
-
Install the rear wheel.
-
Lower the vehicle.
-
Pump the brake pedal several times until a firm pedal is obtained in order to properly seat the pads.
-
Refill the brake fluid reservoir to the proper level.
4/17/2024 3:54:19 PM •
2006 Jeep...
•
Answered
Yesterday
•
3,713 views
2017 Jeep Patriot. Where is the fuse for my passenger side blinker please.
here it is, BCM the causes are :lamps shorted. right side of car if is USA car.blinker switch lever is bad.scan the PCM see if lamp fails or lever fails.or BCM bad.not scanning it is missing THE BOAT big time. OBD2 scanner.any shop in the USA can scan your car even for free some do.ask em. no fuseno relayno blinker flasher modulethe below computer does all that like magic. BCM body brain. TIPMnote the blinkers have regulator or each side.
this post assumes nothing else on the car is failing (all electrics things)
4/18/2024 10:42:35 PM •
Jeep Patriot...
•
Answered
14 hours ago
•
129 views
1987 Jeep dies when temperature hits 180. Then it will start up after its sits for 30 minutes.
First you will need to determine if there is a problem with the electrical system or fuel system. Connect a fuel pressure gauge to the fuel rail to see if you have pressure when the vehicle dies. It it maintains pressure and the vehicle dies, then check to see if there is a spark issue. Fuel issue could be bad/weak fuel pump, bad relay or restriction in fuel delivery system. No spark could be ignition coil, bad computer, bad electrical connection or relay. To check these systems you need special meters and scanners. Best to take to a repair center.
Not finding what you are looking for?