Samsung Washing Machines - Page 6 - Recent Questions, Troubleshooting & Support

The 4E (4C) error indicates that the washing machine has detected that there is a problem with the water supply. The most common reason for this error is a blocked or kinked water supply hose. Aug 23, 2021

How to resolve 4E or 5E codes on your Samsung Washing ...

https://www.samsung.com > ... > Home Appliance About featured snippets• Feedback

People also ask

How do I fix E4 on my washing machine?"); display: inline-block; height: 24px; width: 24px; margin-top: -1px;"> What does E4 mean on a washing machine?"); display: inline-block; height: 24px; width: 24px; margin-top: -1px;"> Feedback

How to resolve a 4E or 4C error code on a washing machine

https://www.samsung.com > ... > Home Appliance A problem with the water supply is usually the result of low water pressure or a low flow rate on the mains water supply to the machine. This means that the ... ‎Samsung United Kingdom · ‎How to clean the detergent...

Too heavy or lumpy wash load is the usual cause if the fixing stays have been removed upon installation.

Dryers don't need Shipping Bolts, only Washing Machines. The drum is supported at the back bearing and at the front by the drum rollers. A washing machine has a completely fluid, free moving drum to allow for uneven loading which is evened out during the spin. https://www.google.com/search?q=shipping+bolts+for+Samsung+dryer+dv42h5200gp%2Fa3 ..

Samsung WA13G7Q1 NOT LOADING WATER

THEN CALL A REPAIRMAN

The pump could either be broken or clogged for your washing machine.Or the drain hose is broken or clogged or the switch assembly is not working anymore. A person that fixes washing machines would need to take a look and see what the problem is.

Defective lid switch. Go to repair clinic.com for help and parts

Old stretched out drive belt. Replace

You would have to remove the top or the case and you will see a plastic box with a lid that directs water to the right section. From there you should be able to work out the problem.

CALL A REPAIR SERVICE , I HAVE SEEN TANKS RUSTED THRU AND SEALS GONE BAD AR RHE SAME TIME

Question edited for clarity. There are a number of videos explaining how to replace the door seal. https://www.google.com/search?q=Samsung+Front+loader%2C+fit+new+door+seal ..

Check the pump is not blocked.

do you mean DC3? Add Door lock switch terminal is broken, loose / broken wire connection. Add door lock switch fault. Main PCB fault.

Unlikely you shorted something as the area is protected from water. Try disconnecting from the mains supply for 30 minutes. You can als Google make model reset sometimes there is a button push combination to reset the logic boards.

Sack it

the suspension rods have busted if your handy enough you can undo a few screws take the top off & change them yourself its quite easy to change the rods they just clip in & out.make sure the power is turned off & the plug is out of the socket so you don't get zapped.

If you open the door, you may see screws that hold the top cover on the frame to the cabinet. Some model use screws and some use pressure clips that you cannot see. If it is pressure clips then the top is just pressed onto the rest of the cabinet and lifts off. IT can be a real challenge to not ding the paint trying to get the top to lift off. Once you do, you should be able to see the whole drawer dispenser. Attached link shows all the parts and views WF45K6500AV/A2 / 0000 Samsung Washer Parts & Free Repair Help - AppliancePartsPros

https://www.republicworld.com/technology-news/gadgets/1e-error-in-samsung-washing-machine.html

information here on repairing or replacing the board. https://www.google.com/search?q=samsung+washing+machine+control+board+repair ..

Please read the repair guide at link.. Washing Machine Will Not Start What To Check How To Fix