Miele Washing Machines - Page 2 - Recent Questions, Troubleshooting & Support

It will be similar to this model https://www.manualslib.com/manual/822285/Miele-T1515.html?page=33 and this one

verifiquw el senson de cierre de puerta, si este no se activa no arranca el ciclo de centrifugado

Try a Power Reset. Remove the wall plug overnight. Press and hold the power button for 12 seconds as you reinsert the plug. Here is the troubleshooting section of the manual. Not much use, but still, it is good to have electronically. https://www.manualslib.com/manual/353788/Miele-Wt-2780.html?page=52#manual ..

Does the pump run before any water enters the washer? If so, then you have a problem with the control board or a problem with the pump control. The more common issue is a siphon. This starts when the water going into the machine gets higher than the end of the discharge hose in your stand pipe or laundry sink. Fixing a siphon is easy - lift the end of the drain hose so that it is higher than the highest water level of the washer. You may need to lengthen the stand pipe. (The maximum height of the stand pipe can be15'; that's maximum height that the pump can push the water.) If you are using a floor drain, then the anti-siphon/air gap system is damaged. I hope this helps. There are parts available for the Miele W1918 online. You need to enter the serial number of the washer to get the right pump or control board. Cindy Wells

Follow the wires back from the water inlet valve to where is joins onto the control board and check the connection to it.

Check the continuity of the element with a test meter. It may also be the Thermostat or Sensor. Videos that might help. Immer Besser.

It appears to be from 2009 and for the Australian market, so you may wish to think about a new one. The control board is $189 AUS. If you do wish to replace the board, let Miele do it. They need to diagnose why the board burned. Then you get warranty on the repair and the part. https://www.google.com/search?q=Miele+5300sci+dishwasher+control+board ..

Question edited for a lot more clarity. I found this hello my name is Jon and i am an authorized Miele service technician and I can help you today. are you sure that you are not misreading the fault or error code? to my knowledge there is no f 1 E error message, just an f13. which is a water intake fault, heater pressure switch. if that is the error you are getting, please look at the following link. it is to the error code list for your machine. please perform the steps listed for the f13 error under the remedy. if the remedy doesn't work I would replace the heater pressure switch and the water flow system. They are very common parts to break on these machine. the parts can be order directly through Miele by calling or going online. phone is the best way to contact them i believe. this way you can actually talk to someone who can help you better. the phone number is 1-800-999-1360. or go online to www.miele.usa.com. the link for the error codes is below. just highlight the link and right click it with your mouse to open it. http://appliancehelponline.com/miele.html thank you. and I look forward to helping you get this machine fixed in the quickest and cheapest way possible.

The error message "fit cover to main dispenser" typically indicates that the cover for the main dispenser (where the coffee beans are stored) is not properly secured. To resolve this issue, make sure that the cover is securely in place and that it is properly aligned with the dispenser. If the problem persists, you may want to consult the user manual or contact Miele customer support for further assistance.

Removing the top lid on a Miele Novotronic 500 washing machine will depend on the specific model of your machine. However, here are some general steps that may help:

1. Unplug the machine from the power supply.
2. Locate the release catch or lever on the top of the machine. This may be located on the front or back of the machine, depending on the model.
3. Press or push the release catch or lever to release the top lid. It should then be able to be lifted off.
4. If you don't find any visible lever or catch, please check the user manual of your washing machine, as some models may have a different mechanism to open the lid.
5. If the lid is still not opening, it may be stuck due to a malfunction or an error. In this case, it is recommended to contact the manufacturer or a professional technician for assistance.

It is important to be cautious when handling the top lid of the machine, as it can be heavy and fragile. It is also important to make sure the machine is not running or plugged in before attempting to open the top lid.

This means that the drain attached to the pump is clogged, remove the drain plug check fro debris and replace...you should be good to go.

you need to check your pipes from tub to exit but remove plug first

Question edited for clarity. Question moved from Computers category. Wash temperatures are not able to be changed, they are dictated by the thermistor sensor and the setting of the EPROM in the control board, however, the 40' Wash temperature refers to the wash labels tags in clothes. About 20 years ago when HE detergents came out, manufacturers reduced water temperatures by 10'C, so although it is a '40' Wash', you should find the temperature is lower. Check it with an infra-red thermometer. https://usermanual.wiki/Miele/W-526.4061114030/html ..

I have a Miele WT2780 where the fan motor stops spinning. This will stop the dryer from working even though the element heats up. The failure of the fan will not blow the air across the heating element and thus into the drum. New motors fitted are around £400 min. I am never going to buy another Miele - mine failed after 6yrs.Another problem is the thermostat can trip. This is a small button inside the machine (TURN OFF MAINS ELECTRIC AND UNPLUG FROM WALL then remove the lid) on the right hand side of the alloy centre channel at the top. It has two wires connected to the switch and in the centre there is a small black button. Press it firmly and it will heat up again. If this keeps tripping then the air duct could be blocked with fluff. This is my next task as mine now trips more frequently so will post back here with instructions.Update 12/10/16 - problem returned so dismantled top of air duct having removed the lid - tight torx screws - inside chamber was full of fluff. Removed and cleaned - all good now!.

Hey did you find the problem I have the same problem with the same washing machine!