LG Dryers - Recent Questions, Troubleshooting & Support

check heating element in stack

It is a gas appliance and can only be worked on by a registered gas appliance technician. They will have access to the codes, they are generally hidden to the general public. Call for service.

Disconnect from power source by turning off breaker or disconnect plug.

Press START/STOP button several times. Reconnect power.

Check power at dryer electrical outlet with DMM if possible.

I have spent half an hour researching the question as I noticed it wasn't answered since I read it last night.. K250 and K251 on the schematic. Is your post the wrong diameter? It looks a standard swap over and none of the parts suppliers mention any modification. That makes mw wonder if yours are mislabeled. https://www.searspartsdirect.com/model/192s9c7uvq-003204/lg-dlg8388wm-dryer-parts https://www.partselect.com/PS16763594-LG-AGM75510755-PARTS-ASSEMBLY-SVC.htm?SourceCode=19&SearchTerm=DLG8388WM&ModelNum=DLG8388WM https://www.google.com/search?q=lg+dryer+dlg8388wm+drum+roller+replacement ..

Two beeps is typical door not closed. Make sure the light goes out when you close the door. Otherwise make sure both Clean Filter and Flow Sense lamps are off. You can run the installation test. See following URL. https://www.lg.com/us/support/help-library/how-to-run-and-installationheat-test-on-an-lg-dryer-CT10000011-20152714315153

refer to owners manual. Since you did not indicate what light is blinking here is a link to LG error codes copy and paste https://www.lg.com/us/support/help-library/lg-error-codes-laundry-dryer-CT10000011-20152310891742

Question edited for clarity and change 'want' to 'won't', a contraction of 'will not'. The check filter indicator is a reminder to clean the lint filter before each use to ensure effective drying every time. The indicator turns off when you turn the cycle knob to select a drying program or when the start/pause button is pressed. Apr 7, 2023

LG Dryer - Error Code List ' LG USA Support

LG https://www.lg.com > ... > SUPPORT > Register a Product

The thermal fuse is faulty. Or the vent is clogged and no gas flow. Or there could be a faulty circuit breaker.

possible flame sensor dirty or bad or burner tube has blockage

It's difficult to determine exactly what may have fallen behind the panel of your LG DLE7100W dryer without a visual inspection. However, it's possible that you may have accidentally detached a small part or screw that was holding something in place. The rolling sound that you're hearing when the dryer is turned on could be a loose part or screw that has fallen behind the panel and is now moving around inside the dryer. This could potentially cause damage to other components if left unaddressed. I would recommend stopping any further attempts to disassemble the dryer and instead, contact a professional technician to inspect and repair the dryer. They can determine what may have fallen behind the panel and take the necessary steps to fix it safely and properly.

Unfortunately, without a picture of the symbol you are describing, it is difficult to give a precise answer. However, based on your description of the symbol and the accompanying burning plastic smell, it is possible that the symbol is indicating an issue with the dryer's motor or belt. The symbol you are describing with the oval and arrows could indicate a rotating part, such as a drum or belt, and the smell of burning plastic suggests that something in the motor or belt may have overheated and melted. It is important to immediately stop using the dryer and unplug it from the electrical outlet until you can determine the cause of the issue and make any necessary repairs. It may be best to contact a professional technician or LG customer service for further assistance and to avoid causing any further damage to the dryer.

I was concerned about the same thing. I am a service tech. I followed the procedures. I changed the orifice and as direct turned the adjustment on the gas valve clockwise to the closed position and put the dryer back together hooked up the gas turned it on and when the burner came on it sounded very loud. I called tech support they said this is normal with the l.p. kit and it is due to the exhaust fan on the dryer. Based on the required heat the fan runs faster or slower. It has a two stage gas valve and variable speed blower in it for the burner. It is a large dryer. As directed make sure you only use flexible or hard metal vent piping from dryer to vent. Never the butler dryer vent

I had the same problem, Check Filter light blinking and beeping, could not select drying type or start dryer. Short story, turned out to be the Less time button was stuck pushed in. Long story, a week before I had replaced the drum rollers and belt, everything was working fine for the week after then this problem. Totally by accident, after trying all the recommended actions (unplugging, pushing buttons, etc.) leaning on the right front corner would stop the beeping and allow the machine to work. Pushing all the buttons, I found the Less time button would not click. Apparently, when I took the control panel off to change the rollers and belt I flexed the control panel enough to misaligne the button and switch. Pulling the back of the control panel loose and making sure the push button and switch were aligned and working correctly everything works fine now.

These are the Error Codes Displayed. https://www.lg.com/us/support/help-library/lg-error-codes-for-laundry-and-dryer-CT10000011-20152310891742

LG Washing Machine Error Codes: Meaning and How to Fix

https://fixappliances.ca > lg-washing-machine-error-cod... Close both water taps. To drain out any trapped water, power the washer back on, press the spin button until no spin is selected, and press the start/pause ... E3 Error

Not enough airflow, and the dryer producing too much heat. Check the vent at the rear, the hose and the flap on the outside wall for lint and obstructions.

To change the bulb on a 2006 model LG f harbor breeze ceiling fan, 69 inch air span, follow these steps:

1. Turn off the power to the fan by flipping the switch or circuit breaker.
2. Locate the bulb cover on the fan, which is typically located near the base of the fan or on the underside of the fan's motor housing.
3. Remove the bulb cover by pressing the tabs or pulling the cover down.
4. Carefully remove the old bulb from the socket and dispose of it properly.
5. Insert the new bulb into the socket and make sure it is securely in place.
6. Replace the bulb cover and turn the power back on to the fan.

Note: Make sure to use the correct type and wattage of bulb for your specific fan model. Check the user manual for the recommended bulb.

NO! Just clean the sensor bars off, located inside the drum, near the lint filter. They are two curved metal strips, about 1/8th inch wide, about an inch apart, and about 4 inches long.
What often happens is when people use fabric softener sheets in the dryer, the sheets give off a waxey substance which coats these bars, preventing the moisture from the clothing from getting to the bars. When that happens, the dryer does not sense any moisture, so it just runs the 6 minute cool down. (note: time dry would not be affected by this, only automatic dry)

at bottom on the back pannel should be a trough that water collects in.............there should also be a micro switch and a float.......when float rises it trips micro switch that starts pump to send water to the collectin tank......... cheers