Kyocera Office Equipment & Supplies - Recent Questions, Troubleshooting & Support

Video help in the links https://www.google.com/search?q=Kyocera+M2040DN+Laser+MFP+Printer.+How+to+change+the+HVT+board ..

https://fixing-tech.com/fix-c2730-error-on-kyocera-taskalfa-4551ci/

The error code C3800 on a Kyocera 3212i printer indicates an AFE error. This error occurs when writing data and reading data does not match 3 times continuously, or there is no response from AFE for 100ms. The following steps can be taken to resolve this issue: Check the connection FFC is not connected properly. Or it is faulty. Clean the FFC terminals of the following FFC and reconnect them. If the issue persists, consider contacting a Kyocera technician or service provider for further assistance.

See troubleshooting section (Chapter 10) of user manual for help. Kyocera-ECOSYS-M5521cdw-Operation-Guide-DSBLS.pdf

See the error code list in troubleshooting section Error Code List - Kyocera FAX System 10 Operation Manual [Page 212] ' ManualsLib For further reference see troubleshooting 10 Troubleshooting - Kyocera TASKalfa 4002i Operation Manual [Page 501] ' ManualsLib All the relevant manuals are here Product Support & Downloads ' Kyocera (kyoceradocumentsolutions.co.uk)

home sancor error poblem

See Appendix A (Page 245) and Appendix B (Page 250) of user manual for help. Appendix A Error Codes - Kyocera KM-1650 Operation Manual [Page 245] ' ManualsLib See Service Manual for further help 2FT ver3 KMA_E.book (manualslib.com)

I would check the connection to the main board as a backup error code can be caused by intermittant connectors.

Question edited for a lot more clarity. Question moved to Kyocera. Nothing to do with a fax card, just make sure the back door is closed. It is normally called the 'Bypass Door' and gives card stock a flat run.

Kyocera FS-2026MFP "Toner Cartridge Improperly Installed"

Copytechnet https://www.copytechnet.com > kyocera-mita-copystar May 26, 2020 - I have tried multiple things and the error message is still there. 1.) tried new toner cartridges. 2.) made sure toner waste basket was ... Thread: 3552CI The toner container is not properly installed Aug 1, 2020 Kyocera M6526CDN Error F375 & F246 & (Y) Toner ... Sep 28, 2021 FS-6025 toner container not installed - Copytechnet Nov 18, 2012 Kyocera ECOSYS M3655idn - Waste Toner Bottle Not Installed Feb 21, 2022 More results from www.copytechnet.com ..

Try to power on the printer without the toner kit and the waste toner box. If the printer stacks again at self test. Next step.... remove one part at time and check if the printer displays any message. First remove the developer unit and power on the machine (normal message "Missing Developer Unit"). Then pull out the fuser unit and power on the machine (normal message "Close Rear Cover"). And finally, remove the Drum Unit and power on the printer (normal message "Call Service 7410"). If the printer still stacks at Self Test, then that is not a good sign. Try to upgrade the printer' s firmware (system + engine). There is a possibility to go further from Self Test. If it does not, then you have to replace the main pwb.

Presumably you mean the WASTE toner container. https://www.google.com/search?q=Kyocera+3511i+it+says+check+toner+container ..

Check Network Connection: Ensure both devices are on the same network.
Restart Devices: Power cycle both computer and printer.
Verify Scanner Settings: Confirm correct scanner selection.
Update Drivers: Install latest printer drivers.
Firmware Update: Consider updating printer firmware.
Inspect Cables: Check all connections.
Contact Kyocera Support: If issue persists, reach out to Kyocera's support.

Thermister failure or too much heat.

Kyocera TASKalfa 1800 - Error Code

Printcopy.info https://printcopy.info > model=TASKalfa 1800 Code: 6020; Description: Abnormally high fuser thermistor 2 temperature (Center) Fuser thermistor 2 detects a temperature higher than 210°C/410°F. More help and videos https://www.google.com/search?q=Kyocera+taskalfa+1800+showing+c6020 ..

Download the operation guide and see section 5 (Troubleshooting). It may help. Product Support & Downloads ' Kyocera (kyoceradocumentsolutions.eu)

Google suggests the following for same error How to guides for KYOCERA Devices - 3101 (google.com)

It sounds like your paper is set to Letter size and you are printing onto A4 size paper? That would result in a 4 cm gap difference. The engineer says the printer is okay, so the problem must be deep in settings of the device sending the prints to the printer. You are famous! https://www.google.com/search?q=KYOCERA+TASKalfa+352ci+leaves+4+cm+gaps ..

Clean the feed rollers. Don't use refilled toner cartridges. Brand new OEM toner every time.

KM-2050 dirty on back of copies

Copytechnet https://www.copytechnet.com > kyocera-mita-copystar Mar 27, 2009 - toner scatter on back of copies. I've noticed a bit of toner build up just below the drum and also a slight bit on the transfer roller. I wiped ... KM 2050 Copying half of the page!!!!! - Copytechnet Sep 9, 2014 KM-1650 & KM-2050 - image compression - Copytechnet Dec 14, 2011 kyocera mita km2050 dirty toner at the back of paper Sep 25, 2020 Miscellaneous KM-5050 faint copies. - Copytechnet Jun 3, 2015 More results from www.copytechnet.com ,,

If your Lexmark printer is displaying the message "replace toner clean printer," and you have already checked that the toner is full, there might be an issue with the toner cartridge or the printer's sensors. Here are some steps you can take to troubleshoot and potentially resolve the problem:

1. Remove and Reinsert Toner Cartridge: Turn off the printer and open the front cover to access the toner cartridge. Carefully remove the toner cartridge and then reinsert it firmly into the printer. Make sure it is seated correctly in its slot.
2. Check for Obstructions: Inspect the printer's interior for any paper jams, debris, or other obstructions that might be interfering with the toner cartridge or the printer's sensors.
3. Check Toner Sensor: The printer has sensors that detect the toner level. Sometimes, these sensors can become dirty or malfunction. Locate the toner sensor (usually a small window or sensor on the toner cartridge) and ensure it is clean and not obstructed.
4. Reset Printer: Turn off the printer, unplug it from the power source, and wait for a minute or two. Plug the printer back in and turn it on again. This can sometimes clear temporary errors.
5. Check Toner Cartridge Contacts: Ensure that the contacts on the toner cartridge and inside the printer (where the toner cartridge makes contact) are clean and free from dirt or toner residue.
6. Check Printer Settings: Verify that the printer settings are correctly set to recognize the installed toner cartridge. If the printer allows you to manually set the toner cartridge type, make sure it matches the actual cartridge installed.
7. Update Firmware: Check if there are any firmware updates available for your Lexmark printer. Updating the printer's firmware may address known issues and improve printer performance.
8. Try a Different Toner Cartridge: If you have access to another compatible toner cartridge, try using it in the printer to see if the issue is specific to the current cartridge.