Krups Coffee Makers & Espresso Machines - Page 3 - Recent Questions, Troubleshooting & Support

Maybe you need to supply the model as well, it's not an error code on the models I'm familiar with. Try editing it into your question or ask a new question with the information within it.

Inside the waterreservoir a little black driver is locked release the driver with a needle or open folded paperclip

ALL DOLCE GUSTO MACHINE HAVE A TEMPERATURE BETWEEN 60C TO 80 NOT OVER

CHANGE MOTHER BOARD

what is the model?

you have to open it. you probably have to replace the seal from under the boiler. quit a bit of doing but if you do it slowly you will be able to make it take photos if you have to

you can only remove the capsule from the capsule holder by means of piercing from under were coffee normally comes out .that is not to say that if the Circolo is not auto. if the machine is auto then it may be that the director motor or gear of director motor is slipt or broken

very bad news, if it keeps heating the thermal safety, will eventually blow due to overheating .you may have a shorted switch or PCB mainboard shorted and is keeping the machine on at all time which is more likely to happen even sow when having internal leaking .

Contact Krups direct. Tell them we sent you

Accessories and spare parts AUTO DOSE COFFEE GRINDER ...

www.krupsusa.com > Beverages > Coffee-grinder > csp

The largest selection of original spare parts and accessories for AUTO DOSE COFFEE GRINDER WITH SCALE GX420851 on Krups's official online shop.

accessories and spare parts for AUTO DOSE COFFEE ... - Krups

www.krupsusa.com > Beverages > Coffee-grinder > csp Accessories Store : buy all original accessories, spare parts for AUTO DOSE COFFEE GRINDER WITH SCALE GX420851 GX420851. Officiel Krups Website.

Try this, remove the tank, the drip tray, the bin on the side and the sliding thing above the bin. Hold down the on and steam buttons while plugging the machine into a live socket, it's either that or the same again but holding down the on button and the program button while plugging it in. You will get a screen that says something like " Remis a something vende" which is French for put it into sale state, you choose "Oui" for yes. It's been a long time since I've done one but that's as best as I can recall. It will zero the coffee counters as well.

Contact Krups to request.

Could be the portafilter ratchet issue

Krups would be a possible source.

Try this, remove the tank, the drip tray, the bin on the side and the sliding thing above the bin. Hold down the on and steam buttons while plugging the machine into a live socket, it's either that or the same again but holding down the on button and the program button while plugging it in. You will get a screen that says something like " Remis a something vende" which is French for put it into sale state, you choose "Oui" for yes. It's been a long time since I've done one but that's as best as I can recall. It will zero the coffee counters as well. https://www.google.com/search?safe=off&rlz=1C1QJDB_enCA643CA644&sxsrf=ALeKk02VetSw_f-MdUcfZ3oveWE2qJRjhQ:1604423278014&q=Krups+EA880810.+How+can+I+hard+reset ..

circuit board need resetting

Plug it in, turn it on and then within 3 seconds touch each of the 4 corners on the touch screen in this order Top left, Bottom right, Bottom left, Top right that should open up the settings options for you, follow your nose after that.

It can cause problems if it doesn't work correctly. To test the thermostat in a drip coffee maker: Step 1: Unplug the unit, empty excess water from the reservoir, turn the unit over, and remove the base. ... Step 3: If defective, remove and replace the thermostat with one of the same rating. https://home.howstuffworks.com/how-to-repair-small-appliances3.htm

Tenho uma krups ea8010 aparece c?digo de erro 05 s? pede a manuten??o e ficam as luzes todas acesas j? fiz todo o processo de limpeza e n?o sai dai

Error code 5 is a result of one of the following:

Blocked water circuit (water meter, pump, distributor, distributor motor, microswitch)

Hi! Did You fixed the problem? I got same error and have no idea whats the point :(