The problem you are experiencing with your Konica Minolta Bizhub C280 not accepting new print jobs after changing the K drum and developer, could be caused by several reasons:
The new K drum and developer might not be compatible with the printer, please check if the new parts are compatible with your specific printer model.
The print queue on the computer may be stuck or corrupted. You can try clearing the print queue by going to the control panel and searching for "printers" and then right-clicking on the Bizhub C280 and selecting "See what's printing" and then "Cancel all documents"
The firmware of the printer may need to be updated, you can check the Konica Minolta website for any firmware updates for your specific model.
The 500,000 page count that you mentioned, could be a "life counter" on the printer, some printers have a maximum page count before needing maintenance, so it might be related to the issue.
The issue may also be related to the print server. You can try resetting the print server or reconfiguring it, or you can try connecting the printer directly to the computer and see if that resolves the issue.
Sometimes, resetting the network settings on the printer can also fix the problem. You can try going to the printer's web interface and find the network settings, and reset them to factory defaults.
It is highly recommended to consult the user manual or the technical support of Konica Minolta for specific instructions on how to perform these troubleshooting steps and avoid causing any further damage.
P-9 Replace the black developer and drum unit.
P-28 Have tech clean the IDC sensor located under the transfer belt forward section (right side of the copier) the rear one towards back of the machine right side There are two clean both
Above two codes should then fix P-21 which is the fault that registration is not right. And Since the Black Image unit is the reference for the other three color in regards to Registration that is why P-9 and P-28 need fix first. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f
The Konica Minolta R2 Super 700 is a high-speed digital duplicator that uses a pump to supply ink to the print head. The problem you're describing, where the P2 pump makes a loud noise, could be caused by several factors.
Here are a few suggestions for troubleshooting the issue:
Check the ink supply hoses for any kinks or blockages that may be causing the pump to work harder than normal.
Check the P2 pump for any signs of wear or damage, such as a broken or worn impeller.
Check the P2 pump's filter for any blockages and clean if necessary.
Check the P2 pump's voltage and ensure that it is within the correct range.
If the problem persists, it may be necessary to replace the P2 pump.
If you're experiencing an installation error with your Konica Minolta C224e drum unit, it may be caused by a problem with the drum unit's sensor. The sensor is responsible for telling the printer that the drum unit is correctly installed and ready for use.
Here are a few steps you can try to troubleshoot the issue:
Make sure the drum unit is properly seated in the printer. The drum unit should click into place when it is properly installed.
Check the drum unit's sensor for any debris or buildup that may be blocking it. Clean the sensor with a soft, dry cloth.
Check the drum unit's connector for any damage or debris that may be preventing it from making a proper connection with the printer. Clean the connector with a soft, dry cloth.
Try to reset the drum unit by unplugging the printer, waiting a few minutes, and then plugging it back in.
If the issue persist, try to replace the drum unit to a new one.
If these steps do not resolve the issue, it may be necessary to contact Konica Minolta customer support for further assistance.
There could be several reasons why your Konica Minolta 360i machine is producing thin, weak color on one side of the page when printing on A3 paper. Some possible causes include:
Ink or toner levels: Make sure that the ink or toner levels in your machine are sufficient. If the levels are low, you may need to replace the ink or toner cartridges.
Print head: The print head may be dirty or clogged, which can cause weak or uneven color. Try cleaning the print head to see if this resolves the issue.
Paper quality: The quality of the paper you are using could be impacting the print quality. Make sure you are using high-quality paper that is compatible with your machine.
Printer settings: Check the printer settings to make sure they are optimized for the type of paper you are using. You may need to adjust the settings to get the best print quality.
If you have tried these troubleshooting steps and the issue persists, you may need to seek the assistance of a technician. It is possible that there is a more serious issue with your machine that requires professional repair.
C-2152 is a trouble code that may be displayed on some Konica Minolta printers. This code generally indicates a problem with the printer's fusing unit, which is responsible for bonding the toner to the paper.
Possible causes for this error code include:
A malfunctioning or damaged fusing unit
Toner or toner waste accumulation on the fusing unit
A faulty thermostat or temperature sensor in the fusing unit
A problem with the power supply to the fusing unit
To troubleshoot and fix this error, you may need to perform the following steps:
Check the fusing unit: Inspect the fusing unit for any visible damage, debris, or toner accumulation. If necessary, clean the unit and check for any loose or damaged components.
Replace the fusing unit: If the fusing unit appears to be damaged or malfunctioning, it may need to be replaced.
Check the power supply: Make sure the printer is properly connected to a working power outlet, and check the power cord for any damage or loose connections.
Check the thermostat and temperature sensor: These components are responsible for regulating the temperature of the fusing unit. If they are faulty, they may cause the C-2152 error code to be displayed.
www.fixya.com > Forum > Printers & Copiers > Konica Minolta
Konica Minolta BizHub C252 - pale colors on the long side · Konica Minolta. ... I have a Konica C250 machine which cannot print red color at all. I had changed ...
www.fixyourownprinter.com/posts/40820
Aug 22, 2008 - On the right hand side of the drum (the part that has the large green handle) that easily slides out. There is a ..... I have konica minolta bizhub c252 colour printer. ... The K light came on a long time ago and is constant on now.
? 0:28
https://www.youtube.com/watch?v=eD8HdNq0MlE
Nov 23, 2011 - Uploaded by Tennants Nottingham
How to clean the drums/i units on the konica minolta number plate printer ... Fix or repair color laser printer with fading, lightprint, or lines samsung clp 300 ... Imaging Unit Reset for Konica Minolta Bizhub C203 / C253 / C353
Main Board for the copier that receive info from the Document feeder is causing that code. Is your machine DS version or none version? Could have the incorrect document feeder for that machine, or the small printed circuit board that come with document feeder is bad. Could try a different document feeder. Might also see if you can have tech come and re-flash the copiers firmware specially the document feeder and or the MFB Board (Multi Function board) is bad.
The second transfer roller might be missing. Is not properly installed. If you open the printer you will see a roller made of sponge like material. That is the second transfer roller. Replace it if above does not work also ensure the transfer belt is properly installed. that is across from it in the machine.
1. Turn OFF the main power switch.
2. Turn main power switch ON while pressing the Reset key.
3. Touch [Trouble Reset].
4. Check to make sure that [OK] is displayed and it has been reset.
5. After turning off the main power switch, turn it on again more than 10 seconds after and check if the machine starts correctly.
If the code comes back replace the fuser unit (HOT PART) Do not continue to reset. Could start a fire that would ruin a perfectly good day! Once the fuser is replace may require to reset the it again
C1183 is for Finishing Option Elevator Drive Failure. Most of the time when I see this code it is because 1 or both bins are not fully inserted into their slots. The bins when all the way in will trip small switches to tell the machine where the bins are. In your case this may not be true due to the noise you are hearing unless the elevator has already driven the unit all the way to the top or bottom.
C11BO is for Finishing Option Stapler Unit CD Drive failure. I have never seen this code come up before but as you can see, both of these codes are coming from the Finishing Option which you have just installed. It is very possible that the unit has some shipping or other damage and there is nothing you have done wrong. If it were just the C1183 I would feel differently.
I would start by checking the stapling unit and make sure that you got the packing tape and materials out of the inside of the finisher that hold the stapling unit during shipping. Most likely the 1183 code was from the bins but I am not sure of that as it could also be a shipping damage issue. Hope this helps!
Good Luck and Thank You for using Fixya.
WheatlandServices
