Konica Minolta Magicolor - Recent Questions, Troubleshooting & Support

Transfer separation Roller open the machine where the transfer belt is see a sponge looking roller on the other side ensure it is properly installed or replace it. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Hi)I had some interesting solution for 001b error:there was incorrectly installed, not clicked in self seated place, and I've just clicked it to one's place - I only need to push the big Transfer block out ))

Here is there website for parts. please rate my answer. thanks



http://printer.konicaminolta.com/service/spares.asp

The second transfer roller might be missing. Is not properly installed. If you open the printer you will see a roller made of sponge like material. That is the second transfer roller. Replace it if above does not work also ensure the transfer belt is properly installed. that is across from it in the machine.

C1183 is for Finishing Option Elevator Drive Failure. Most of the time when I see this code it is because 1 or both bins are not fully inserted into their slots. The bins when all the way in will trip small switches to tell the machine where the bins are. In your case this may not be true due to the noise you are hearing unless the elevator has already driven the unit all the way to the top or bottom.
C11BO is for Finishing Option Stapler Unit CD Drive failure. I have never seen this code come up before but as you can see, both of these codes are coming from the Finishing Option which you have just installed. It is very possible that the unit has some shipping or other damage and there is nothing you have done wrong. If it were just the C1183 I would feel differently.
I would start by checking the stapling unit and make sure that you got the packing tape and materials out of the inside of the finisher that hold the stapling unit during shipping. Most likely the 1183 code was from the bins but I am not sure of that as it could also be a shipping damage issue. Hope this helps!
Good Luck and Thank You for using Fixya.
WheatlandServices

Toner level cyan is bad. Replace the cyan image unit. and the Cyan toner

https://www.google.com/search?q=Konica+Minolta.+Why+doesn%27t+the+blade+clean+the+magenta+after+printing+color ..

Question edited for full 'make model (what it is)'. Question moved to make model category. See if there is a broken piece sitting in the bottom of the machine. It is small enough that you can turn it upside down and shake it. All machines have some type of guide rail and a positive lock at the end. https://www.google.com/search?q=1600w+printer+toner+cartridge+loose ..

Reboot the printer. This often clears the service message, and printer operation can resume. If the problem persists, contact Technical Support. https://www.konicaminolta.com/?_ga=2.925553.1712686740.1643574641-1075806822.1643574641

clean the rollers and or replace them. Also replace the roller clutch Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Need to set A4 size default on the printer driver itself.
Go to Printers and Faxes / Konica Minolta 2490MF right click/ Printing preferences /
Create a "Easy Set" with a new name. Set all paper sizes to A4. Save the new settings to the new Easy Set.
Click apply.

should be o.k.

KONICA MINOLTA 1690MF ERROR: process error - belt (clear by cover) SOLUTION: Open and close the scanner unit. Reseat the Image Unit and cycle the power to the machine. If the error persists and the machine is covered by warranty, a printer exchange is recommended. KONICA MINOLTA SUPPORT PAGE: https://kb.mykonicaminolta.com/selfservice_bus_anon/microsites/search.do?cmd=displayKC&docType=kc&externalId=TAD-doctad227704html0&sliceId=&docTypeID=DT_TAD_1_1&dialogID=10562139&stateId=1%200%2010556672

Deleting reset Minolta Magicolor 1600W drum / Xerox Phaser 6121 / Oki C110 / Epson C1600 and derivatives identical engine. All the instructions in the link. Can be translated into google. Toner do drukarki materiay eksploatacyjne Kasowanie reset bbna Minolta...

did you change toner from printer menu or rotate toner rack manually ??? this printer toners must be changed from printer menu, because printer counts toner there is no chip on toner.

replace the belt

put a proper konica minolta toner in not third party

you do not reset toner you replace it

replace the yellow image unit

The second transfer roller is bad or missing or the clutch and solnoid are bad. also check the plastic cover that you have to pull down when replacing the transfer belt