Konica Minolta bizhub - Recent Questions, Troubleshooting & Support - Page 5

Have you checked the default setting in control panel for that printer?

Replace the cyan image unit. Did buy a third party???

Did you replace the main board??if so the a Chip is missing which is required on the board, have the old board if so remove from old place on new board. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

did you mean 3451??? Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

A4 paper equals 8 1/2 x 11 paper wrong paper setting Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Utility/Counter -> Details -> [STOP][0][0][STOP][0][1]
Go to counter and clear the life of the developer and drums and then run F8 from functions.

Reset your Toners and Imaging units for Minolta Bizhub and CF series.
http://www.chipreset.eu

Replace Developer DV116, and use good quality toner. bad toners damages the Developer .

C-3421 = Fusing heaters trouble
To Reset:
1. Turn OFF the main power switch.
2. Turn main power switch ON while pressing the Utility/Counter key.
3. Touch [Trouble Reset].
4. Check to make sure that [OK] is displayed and the it has been reset.
5. After turning off the main power switch, turn it on again more than 10 seconds after and check if the machine starts correctly.

If error code returns a technician is needed to replace fuser section. Call local dealer with error code and tell them to make sure a tech brings a fuser assembly.

It is a fuser error.

Try resetting. To reset a Rank A error follow these steps:

1. Turn OFF the Main Power Switch.
2. Turn Main Power Switch ON while pressing the Utility/Counter key.
3. Touch [Trouble Reset].
4. Check to make sure that [OK] is displayed and the it has been reset.
5. After turning off the Main Power Switch, turn it on again more than 10 seconds after and check if the machine starts correctly.
If the error recurrs then do the following:
1 Check the Fusing Unit for correct installation (whether it is secured in position).
2 Check the Fusing Unit, PWB-M and PU1 for proper connection and correct or change as necessary.
3 Change Fusing Unit
4 Change PWB-M
5 Change PU1

Replace Developer , and use good quality toner. bad toners damages the Developer .

That sounds like a white balance issue to me. Do you use manual white balance setting or auto white balance?

What are you trying to reset?

To print the transmission report:

1. Press the [Fax/Scan] key to display the Fax mode screen.
2. Touch [FAX Menu].
3. Touch [TX Report] on the Set 1 tab.

4. Select how to output the report, and then touch [Enter].
– Default: The transmission report is printed according to the previously specified method.
– ON: The transmission report is printed with each transmission.
– If TX Fails: The transmission report is printed only if the fax could not be sent.
– OFF: The transmission report is not printed, regardless of the transmission result.

Thread 2704 Abnormality in the black charging unit. Possible causes: Black charging unit HV Unit Print Control Board Best guess is that you have a faulty charge unit. Try swapping the units around with another colour and see if the fault code shifts.

this is a waste toner box error the waste toner box could be defective or the full sensor is defective i would start with replacing the waste toner box and clean the sensors on the door with some canned air the waste box and the sensors are located inside the lower front door the instructions on how to remove the waste box are on a label on the inside of the door

Go into the PDS settings and change tab from single page to multiple page.

My Friend You must do general service in your photocopier and then you must program your machine.

sintam se cumprimentados, estou com um problema na minha bizhub 211 ela pede para contactar tecnico (M1).como faco

Este código significa que la vida las partes de su desarrollo + unidad de imagen se ha caducado. Ahora es el momento de reemplazar las partes.