Jensen Car Audio & Video - Recent Questions, Troubleshooting & Support

Do the Screen Calibration. https://www.google.com/search?q=Jensen+9022+touch+screen+is+out+of+alignment ..

Try Jensen support for that detail. https://jensenmobile.com/support/ https://jensenmobile.com/shop/multimedia/cr271ml/

hair dryer if just moisture if water [failed seal or damaged cover ] and need to unscrew ans pry apart --but if water most likely electric circuit damage

Your Jenson model as written only appears here on Fixya in your question. The Jenson modelling numbers don't follow what you wrote so your model number 'EOA 7P' is not valid. https://www.google.com/search?q=jensen+eoa+7p ..

It sounds like there may be an issue with the mechanical components of the DVD player, specifically with the tray. Here are some troubleshooting steps you can try:

1. Check to see if the emergency eject feature is working. There should be a small hole on the front of the DVD player, and you can use a paperclip or a similarly sized object to push the button inside. This should manually eject the tray.
2. Make sure that the DVD player is receiving power. Double-check all of the connections and fuses.
3. Reset the DVD player by disconnecting the power for a few minutes, then reconnecting it and trying again.
4. If none of the above steps work, it may be necessary to take the DVD player apart and check the mechanical components for damage or wear. However, this is not recommended unless you have experience with electronics repair.

If none of these steps resolve the issue, you may need to seek the assistance of a professional electronics repair technician.

No, you cannot use a 270 watt amp kit on a 1000 watt amp. The wattage of the amp kit must be equal to or higher than the wattage of the amp it is being used for.

This video may help you https://www.youtube.com/watch?v=VC89DgWJlYw

1200 Watts at 12volts is 100 Amps. At least 16mm on a short run.

yes you can watch video
I alredy did it in my jensen
all you have to do is:
xvid avi
video codec: mpeg4
video bit rate: 887kbits/s
video size: 576x320
aspect ratio: 16:9


set this setting in total vide converter
do the convertion and that's.

Single 2" voice coil

Ground the parking brake wire

My guess would be internal short

Your extension voltage has a problem

I used to own Jensen cd player for a while but I can't remember the solution of loop loading. Check Jensen cd-players manuals http://jensen.manymanuals.com/cd-players

Possibly failure of the selector

There is always a chance that you "bricked" the unit with the update. IT happens. When you get to the cross hairs you are supposed to hold your finger in the middle till it asks for the next step. IF it wont go to this, then can you retry the whole process over again. If not you have bricked it and it has to be sent in for reflash

In the back of the set you should find a small 'spade' type fuse, replace with Fuse: 15-amp, mini ATM type There is a fuse holder in on the yellow wire on the wiring harness, pull out the unit and replace fuse. User manual: http://www.jensenmobile.com/docs/common/UV10/UV10_OM.pdf Wiring diagram http://www.manualslib.com/manual/674477/Jensen-Uv10.html?page=4#manual Good luck.

I just purchased the VX7020 and went to Settings-Language-typed in 5,4,3,2,1,0 but the menu never came up. Any ideas?

Try the following which i managed to get from POWER ACOUSTIK technical support:

Multi-region for PTID4006T, 406T, 4005, 405, 8006T, 8004, 4003, 5000, 5800, 5300, 530.

1. Turn the unit on and insert a DVD disc. The unit will display LOADING.

2. While the DVD player is LOADING press the following keys:
SET-UP, then press 0, 0, 0, 0 key (0 four times), then ARROW DOWN key (to change the zone to region all 0), then BAND/ENTER key and SET-UP

3. To finish the procedure, push the EJECT key. The disc will eject... Wait and the DVD disc will re-load and play.