Hoover Washing Machines - Recent Questions, Troubleshooting & Support

temperature sensor has shorted or is an open circuit
Check the wiring to the thermistor and if necessary replace the thermistor

Hoover Washing... | Answered on Jan 12, 2019

You have faulty transmission or/and clutch.
Clutch is on the bottom of the transmission , next to the pully.

Hoover Washing... | Answered on Jan 11, 2019

You have had a leak.
You can disconnect the hose and empty all the water out of it, then leave the hose in the sun to heat up, this will SOMETIMES reset the water stop, if not you will need a new hose.

Hoover Washing... | Answered on Jan 11, 2019

Error code E09 means there is something the matter with the part in the washing machine control board that drives the motor. Fixing a control board error can be complex. You can try:
Switching off and unplugging your washer when you do this i suggest waiting about 5 minutes before plugging in since your machine can store energy even after a few seconds of being unplugged.
Checking the wiring and connections to the control board

Hoover Washing... | Answered on Jan 10, 2019

Please see

Where it says there is a problem with the motor speed sensor or sometimes with the motor itself

Hoover Washing... | Answered on Jan 09, 2019

(Obviously - you have to check the tap/faucet is turned on.)
Assuming this is not a new machine and has been running fine - the 1st thing to check is that there is no blockage in the water inlet pipe - sometimes a grain of sand/dirt gets into it and this can block it up - there is often a filter there which can be pulled out with a long nosed pair of pliers and sometimes there can be dirt under there.
If this does not help then there could be a problem with the electronic water inlet tap or with the water height sensor which could be blocked - leading the machine to think there is already enough water in the machine.
lastly there could be a problem with the electronic card which controls the machine.

Hoover Washing... | Answered on Jan 09, 2019

source :https://www.espares.co.uk/advice/careandmaintenance/how-to-fix-an-e14-error-on-a-hoover-washer-dryer

Error code E14 relates to a water heating or control board fault.
  • Switch off and unplug your washer dryer.
  • Check the temperature sensor as well as the wiring to it.
  • Check the water heater element.
  • Check the connections to the control board and the board itself.

Hoover Washing... | Answered on Jan 09, 2019


Hoover Washing... | Answered on Jan 03, 2019

take down make & model # contact manufacturer technician line, you may also turn your power on and off to wi-fi and retry to see if it works

Hoover Washing... | Answered on Dec 29, 2018

E08 is the motor speed sensor error code. Suggestion: Try a cycle with very few garments and see if it completes the cycle.

Hoover Washing... | Answered on Nov 27, 2018

Try unplugging for 5 minutes. That may reset electronics

Hoover Washing... | Answered on Nov 23, 2018

You will more than likely have to replace the dispenser box. Sone models u can pull it apart and run pipe cleaners through it

Hoover Washing... | Answered on Nov 10, 2018

Check drain hose first.

If you do not find any blockage, then you will need to access the pump, remove pump hose and look for blockage in there.

If there is no blockage at all, then either the water level switch, a faulty pump, a wiring problem, or a faulty timer board can be cause the machine not draining.

Hoover HF7 160E... | Answered on Nov 09, 2018

Not finding what you are looking for?
Hoover Logo

2,502 questions posted

Ask a Question

Usually answered in minutes!

Top Hoover Washing Machines Experts

shaun taylor

Level 3 Expert

1527 Answers

Hjalmer Lamminen
Hjalmer Lamminen

Level 3 Expert

552 Answers

Steve F

Level 3 Expert

1115 Answers

Are you a Hoover Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides