Hilti Drills - Recent Questions, Troubleshooting & Support

How is it acting? All posts need some form of explanation of the issue rather than a vague statement. Start with 'make model (what it is)' as first three words. Then what is wrong and what you have tried. Proof read it, make sure it is properly capitalized and punctuated and then press Post. Refresh the page to see it online. ..

According to the operating instructions for the Hilti TE 6-A22, if the rotary hammer is running but there is no hammering action, it could be because the rotary hammer is too cold. To fix this, bring the tip of the drill bit into contact with the working surface, switch the rotary hammer on and allow it to run. If necessary, repeat the procedure until the hammering mechanism begins to operate. Also, ensure that the function selector switch is set to "Drilling without hammering" . If this doesn't work, you may need to take your tool to a professional repair service. You can find a list of authorized Hilti service centers on their website.

1. try to pull the trigger more back then its stand free , because i think that a dust ring insite the trigger was come loose and get inside the trigger so it will not fully come back in its normal rest position but its stands maybe a little fraction triggered , replace the switch .

google Parts diagram for a hilti TE 6- A22

notify hilti or nearest tool repair shop or online search

Da biste prona?li dijagram shemu za Hilti TE 3-M, preporu?ujemo da posjetite slu?benu web stranicu tvrtke Hilti i potra?ite podr?ku ili kontakte za tehni?ku podr?ku. Mo?da ?e vam biti potrebni serijski broj ili druge specifi?ne informacije o va?em ure?aju kako biste dobili odgovaraju?e informacije. Tako?er mo?ete poku?ati prona?i dijagram shemu na mre?i tra?enjem po nazivu modela i broju dijela, ili se obratiti Hilti servisu za podr?ku ako trebate dodatnu pomo?.

E 253 Temperature too low refer to instructions.

You fill it. Special oil it says here, but the video it looks like motor oil for a car. https://www.google.com/search?q=Hilti+TE76%2C+oil+capacity

There is a one minute video, but it is a 30 minute videos speeded up! The fill cap takes a large Allen key. It is not the cap under the bottom of the gearbox, it is situated in the top of the drill. https://www.google.com/search?q=Hilti+TE+17+Oil+change ..

Hi. My hilty te75 lose force in hammer. my email is [email protected]

There are a couple of differant versions of the 650. Open up your chuck as wide as you can. Like you were putting a big bit in it. Look inside to see if you see a screw head. It might be slotted or torx. It will be left handed threads which means you will turn clockwise to remove. Once that screw is out you lock the front of the chuck in a vise and right behind the chuck will be a place to put a thin wrench. Turn the wrench in a counter clockwise motion away from the chuck.

inside the chuck you will see a screw, remove the screw and chuck . A small punch with minimum forced with a small hammer to move the chuck dogs toward the end on the chuck . The chuck was opened to far and is a mechanical bind ..

chuck damage--debris - failure

Hi
220ml of synthetic 68 gear oil.

Hope this helps

Drill with a carbide drill and screw in a deck screw into a plastic plug in the hole..

Get it from Hilti direct. There is a Czech site blasting all the results and charging for them. https://www.hilti.ca/c/CLS_POWER_TOOLS_7124/CLS_ROTARY_HAMMERS_SDSMAX_7124/CLS_CORDED_ROTARY_HAMMERS_SDSMAX_7124/r4902202 https://www.google.com/search?q=hilti+te+50+avr+parts+diagram ..

It's a replaceble part correct? Check ebay. or [email protected] ' (626)-656-5982

Question edited for clarity. Question moved from Computers to Hilti. Here are parts suppliers. https://www.google.com/search?q=TE+76+Hilti+parts ..

https://www.youtube.com/watch?v=XTu5XU8sYxg