You can purchase one from Black and Decker, Vector was purchased from them in 2006, here is the link;
http://www.dewaltservicenet.com/servicenet_home.aspx?r=No%20%Results
This one?
https://www.ebay.com/itm/335145703247
They are a bit of a gimmick, and of course are made for $2 in China.
The way they work is that they contain a small rechargeable NiMH battery. You can charge it via the wall adapter, or you can turn the crank which operates a small generator to charge the battery. It is likely that you can't run it directly from the mains, but it should light when you remove the charging cable and switch it on.
..
It carries an LED Module, so they aren't like replacing a halogen bulb, you have to replace the whole module with the LED.
Just replace the whole lamp for 10 bucks!
I remember that light, its a halogen bulbed searchlight with a sealed lead acid battery. Both technologies are obsolete, your battery is likely aged and can be replaced I think its a 17ah and about , $40. For a little more money they make a lifepo4 in the same format. If it were me though Id send it to the dumpster, led powered by lithium now equal its output but fit in your pocket.
To my knowledge this item has been discontinued by Coleman and is no longer available. However, I've listed basic instructions on changing batteries. Here's a link that you could watch for the disassembly for your flashlight type.
high power flashlight ct-50 (youtube.com)
Locate the battery compartment on the Coleman CT 50 flashlight. This is usually at one end of the flashlight and is secured with a cap or cover.
Depending on the design, unscrew the cap or remove the cover to access the battery compartment. Some flashlights may have a twist-off cap, while others may have a sliding cover or other mechanisms.
If there are existing batteries in the compartment, carefully remove them. Pay attention to the orientation of the batteries, noting the positive (+) and negative (-) ends.
Insert new batteries into the compartment, ensuring they are placed in the correct orientation. Match the positive and negative ends with the markings inside the battery compartment.
Once the new batteries are in place, securely put back the cap or cover. If it's a screw-on cap, tighten it until it's snug. If it's a sliding cover, ensure it clicks into place.
Turn on the flashlight to check if the new batteries are working correctly. If the flashlight doesn't turn on, double-check the battery orientation and make sure the connections are clean.
If the old batteries are disposable, make sure to recycle them properly. Many communities have specific recycling programs for batteries.
Always refer to the user manual or any included instructions for your specific flashlight model, as the steps may vary. If you don't have the manual, you can often find it on the manufacturer's website or contact Coleman's customer support for assistance. Additionally, be mindful of the type and size of batteries recommended for the flashlight to ensure optimal performance.
It should take 10-12 hours, any longer the battery is no good, you can test the battery using a Volt Meter, the battery should be reading 12 volts, any less and the battery will need to be replaced. You can order a new one from Black and Decker, they purchased Vector in 2006, here is the link; http://www.dewaltservicenet.com/servicenet_home.aspx?AspxAutoDetectCookieSupport=1
Whether or not to buy hiking shoes really depends on what kind of walking you plan to do and how often.Hiking boots are helpful for rougher terrain and for gripping. If you plan to mostly walk on flat ground, you can consider getting good walking shoes instead.
Question edited for clarity, 'full make model (what is is)' spelling of maker and all the missing letters. Please don't type in all CAPS.Question moved from Cameras category.Duplicate question deleted. Refresh page to see your question.Make sure the polarity of the batteries is correct.Contact Rayovac Support for help and warranty replacement.https://www.google.com/search?q=RAYCOVAC+SP8DTP..
I found four different versions of the AD100 operator's manual using the Furuno USA Get Support link, https://www.furunousa.com/en/get_support . The current link is https://www.furunousa.com/en/support/ad100 . Click on the Documents and Tech Info tab. The manuals depend on the age of the Gyro analog to digital converter.
I hope this helps.
Cindy Wells
