Gentron Electrical Supplies - Recent Questions, Troubleshooting & Support

No that is definitely not good news is it! All the reasons of what causes the bad news https://www.google.com/search?q=Gentron+GG10020+Generator+doesn%27t+start ..

There is limited help in this link https://www.google.com/search?q=Gentron+Portable+Generator+-+GG10020+wiring+diagram But you could phone them. Here is your manual. https://www.absolutewaterpumps.com/media/blfa_files/gg10020_owners_manual_w_parts.pdf ....

buy the manual for it try here https://generatorguru.com/gg10020-gg10020c/ or search https://search.brave.com/search?q=gentron+g+g+10020+generator&source=web

contact gentron

Sounds like pieces of the flywheel fins-if they are plastic. Some are.

You can get a manual from your diesel generator supplier. Usually, user manual will be delivered along with diesel generator. If you are looking for a silent diesel generator, please refer to this reliable generator manufacturer: https://www.dieselgeneratortech.com/silent-genset/quiet-diesel-generator.html

The anti-afterfire solenoid is typically powered from battery when the ignition switch is in run or start position. If yours has two wires, one goes to frame ground and the other to the ignition switch.

Please ask your supplier for help, i think it is fast to solve the problem. If you need Cummins genset or Perkins genset, please visit website: www.dieselgeneratortech.com.

Hi! We have a put together a guide here to assist you in these situations. It will guide you through testing, repairing and finding any parts you might need for the Generator. : https://www.generatorguru.com/need-help/ Regards,The Generator Guru Team

We hold the switch you need :) https://www.generatorguru.com/gg10020-gg10020c-1/?sort=featured

Plug gap is not hyper-critical. Too close is usually worse than too wide. If you set the gap at .035 and the recommended gap is .025, it'll still run. Or set at .035 and recommended is .045. We're talking about the thickness of 2-3sheets of paper difference.

You've got an air leak somewhere. Running better with the choke closed is the clue. Air is entering somewhere else and by closing the choke you are basically adjusting the air/fuel ratio to be more correct.With a combustible carb spray and red nozzle pipe, you can lightly spray around the carb as the engine runs and see where the running changes and that's your leak point. Keep the spray away from the carb inlet so you don't get misled. The carb could also have gunked up gas deposits. Clean the carb also.Re-check it.

You change the oil after used for a certain period of time. If not used often you do not change the oil as often as in a car. The manual you have will give you so called recommended intervals which in most cases are a tad too often.

https://www.google.com/search?client=aff-maxthon-maxthon4&channel=t27&q=gentron%20pro2%20generator%20welder%20manual

Gentron Pro2 Owner Manual

You must be more specific. Here's a link to a .pdf manual for A Gentron generator; perhaps you may find your generator manual within this thread.http://www.searspartsdirect.com/partsdirect/user-manuals/GG3500-Gentron-GENERATOR-manual

http://www.houzz.com/proMatch/electrical-contractors/generator-repair/c/sacramento?m_refid=olm_google_732295438_39218321915_kwd-127850478724&pos=1t1&device=c&nw=g&matchtype=b&gclid=Cj0KEQiA25rFBRC8rfyX1vjeg7YBEiQAFIb3bxNjWNZJxP79OU5-Jrc7IM4l21Ute7MZEg15r1t0QjAaAlae8P8HAQ Generator Service CD Power Commercial and Industrial Generator Experts