General Washing Machines - Recent Questions, Troubleshooting & Support

Ideas in the link, but this is a commercial washing machine. https://www.google.com/search?q=super+general+washing+machine+E53+code ..

We don't have these strange machines in north America. If it is new it is under warranty and needs a claim. It sounds like the main board has failed, or the timer. Not finding that model https://www.google.com/search?q=Super+General+Washing+Machine+SGW10225 ..

Question edited for clarity. E3 is a generic 'Off Balance' code If you receive an E3 Error code, your washer may be unbalanced. This could be caused by the washer being too tightly packed, or clothing not distributed evenly. This will usually occur during the spin cycle. Stop the spin cycle.

E3 - Error Code - Stacked Laundry Center - Whirlpool Canada

F8 is taking too long to fill. Check the filter screens on the rear hoses. The F8 E1 or Lo FL error code means your washer is not detecting the correct amount of incoming water. If the washer has an F8 E1 error or LO FL error, the door may be locked, and the control may be unresponsive. Aug 21, 2023

F8 E1 or LF or LO FL Error Code in Display - Washers - Amana

..

did you get the 4 rubber washers that go in the hose ends?

The error code E12 on a Super General washing machine indicates a drainage issue. This could be caused by a few different things:

1. Clogged drain hose: The drain hose that carries the water from the washing machine to the drain may be clogged. Check the drain hose to make sure that it is not blocked by debris.
2. Drain pump: The drain pump is responsible for pumping the water out of the washing machine. If the pump is clogged or damaged, it will not be able to pump the water out and the machine will display an E12 error.
3. Drain filter: The drain filter is located in the drain pump and is responsible for trapping debris that may clog the drain hose. Check the drain filter to make sure it's not clogged.
4. Control board: The control board manages the washing machine's functions and if it's faulty it can cause the drain pump to run continuously and display the E12 error.

It's recommended to first check the drain hose, drain pump, and drain filter to see if they are the cause of the issue. If these are all clear, the problem may be with the control board, which will require professional repair. Please be careful when checking the drain pump and filter, as the water may be hot if the machine is in the middle of a cycle.

If the water level in your Super General SGW720N top load automatic washing machine is not stopping and is overflowing, there could be a few possible causes. Here are a few steps you can try to troubleshoot and fix the problem:

1. Check the water supply hoses: Make sure the water supply hoses are properly connected and there are no visible signs of damage or leaks.
2. Check the water level sensor: The water level sensor is responsible for controlling the water level in the machine. If it is not functioning correctly, it could cause the water level to continue rising. You may need to have the sensor cleaned or replaced by a professional.
3. Check the water inlet valve: The water inlet valve controls the flow of water into the machine. If it is not functioning properly, it could cause the water level to continue rising. You may need to have the valve cleaned or replaced by a professional.
4. Check the control board: If the problem is not with the water supply hoses, water level sensor, or water inlet valve, it is possible that there is an issue with the control board. You may need to have the control board inspected or replaced by a professional.

If you are unable to resolve the problem on your own, it is recommended to contact a qualified service technician or the manufacturer for further assistance. It is important to follow the manufacturer's instructions when attempting to repair or troubleshoot your washing machine to avoid causing further damage or injury.

Question edited for a bit of clarity. This doesn't appear to be a General Electric (GE) machine and looks to be an Arabian machine. We are in North America. This link might work better for you in your county. https://www.google.com/search?q=super+general+automatic+washing+sgw721+e+error+code ..

Try to clean the discharge pump filter first (Instructions in the Use/Care manual).

If the drain pump is working, it's most likely related to the pressure switch. Check out this posting:

http://www.fixya.com/support/t9807344-ge_front_load_washer_stops_45_min_35_min

i would try to clean the trap out at the bottom, there is a panel on the bottom take that off and clean out the trap, it looks like a turn dial, something like that has happend to me, it cant hurt to try

e3 mean to much water in washer,check inlet valve, are call a techicain to solve your problem

It has a blocked sensor pipe. Clean and service the machine.

Too much water in the machine. Check the drain pump, outlet pipe and filter if any.

check out this youtube video on e60 error https://www.youtube.com/watch?v=-6iNKH9qhKU

check voltage from switch to power board if ok bad display

I have super general washing machine model is sgw 620 this machine coming error E5

i don't know. i repaired same condition on different washer. it was the lid safety switch/pin contact. i tested by pushing pencil in hole where safety pin goes. DO NOT USE MACHINE WITHOUT WORKING LID CLOSED SAFETY LOCK. you could break an arm / hand. i slid top off washing machine and moved lid switch back so ' lid pin ' would contact safety switch. if this is the cause, you may need to replace this low cost switch.

go to google. and enter your machine model # for wiring diagrams.

you can google you super general swg 1201 E01 error for instructions to trouble shoot. or try you tube.

The drain on the wall is called a Stand Pipe. It is designed to be higher than the washing machine so that you do not flood the building every time you do a load of wash. The Machine has a built-in pump to pump the water out of the machine when needed. You will need to attach a washing machine drain hose to the machine. You should be able to find one at Lowes or Home Depot. https://www.lowes.com/pd/bosch-drain-hose-extension-kit-gray/1000024537?cm_mmc=shp-_-c-_-prd-_-app-_-google-_-pla-_-186-_-sosaccessories-_-1000024537-_-0&kpid&k_clickID=go_625713068_34614756550_111134534590_pla-261169297148_c_9027729&gclid=EAIaIQobChMIwc_2u8_-4AIV9x6tBh1fSA3fEAQYAyABEgJjjPD_BwE

Run the machine empty to see if you can clear some of the soap residue, E-4 is "suds lock" error and is usually due to using too much detergent.