Frigidaire Freezers - Recent Questions, Troubleshooting & Support

You can try reseating the controller. UNPLUG THE FREEZER FROM THE ELECTRICAL OUTLET. Get a wide putty knife and insert it between the door and the controller bezel on the right side of the controller. Pry the controller out toward the top first (comes out easily) by twisting the putty knife handle so the top of the controller pops out and then grab the controller toward the bottom and pull it out as straight as you can. Get some dielectric grease and put it on the pins at the bottom on the back of the controller you removed from the door. Alternately, you could put wd40 on a cotton cloth and wipe the contacts. Make sure not the leave any debris on the pins other than a little bit of grease or wd40. Insert the controller back into the door and plug the freezer electrical cord back into the outlet. I had some problems with the line voltage coming in my house. For a while the lights would flicker. I believe that this was a contributor to the problems I had with my freezer, which have lasted about five months now. I would intermittently find that the display was all lit up or that the led number segments would be dark, but a little red led was lit. Simply unplugging and replugging at the electrical outlet seemed to do the trick. Finally it seemed like it completely malfunctioned, not restarting after unplugging and replugging. Just dead. I finally pulled off the controller and put the dielectric grease on the pins and then whalla, it came on again without issue...well for 15 minutes so far. I had a feeling that the issue was the controller all along because the freezer itself never seemed to have any problem getting cold or setting the temp, just this problem of shutting down every so often (2-5 times a week). I'll post back again with an update.

Question edited for clarity and add maker. Question moved to correct category. 16 cubic feet for that series, the '16' in the model number. https://www.google.com/search?q=Frigidaire+FFU1424DW16+freezer+Cubic+feet ..

Question edited for clarity. Question moved from Washing Machines category. It looks to be a standard 20 cubic feet freezer and has '20' in its model number. you can also measure it internally in feet and multiply length x width x depth. https://www.google.com/search?q=frigidaire+mfc20m4fw3+review ..

The error code -H9 on a Frigidaire upright freezer typically indicates a communication error between the control board and the display board. To troubleshoot this issue, try unplugging the freezer for a few minutes, then plugging it back in to see if the error code clears. If the error persists, it may be necessary to replace one or both of the boards. Contact a qualified appliance repair technician for further assistance.

According to the Frigidaire website, the cubic feet for the Frigidaire stand up freezer model MFU23BW4 is 23 cubic feet.

the outside one should just pull off the plug in the bottom can be removed by using a vaccum or blow air into the hole once the outside plug has been removed

Many reasons why it may be loosing temperature. Such as Defrost problem, fan not running, sealed system problem, compressor problem

if have an amp probe [multi-meter] when turns on check amp draw on motor ----motor failure ---thermostat failure --no freon

Hey friend, thanks for your inquiry!

Within your Frigidaire freezer the error code "FF" stands for freezer failure. I would perform a reset on your appliance which can be done by either unplugging the power cord or flipping the household circuit breaker. Once the freezer has come back on you should be able to push the "Down" button three times to start it back up.

If that does not correct the issue Please respond back I would like to assist you with any additional information. Hope this helps to some degree. -Matt

It is under the temperature is has been set to. It should stabilise in about 4 hours..

Question edited for clarity. Question moved from Cars and Trucks!! This has all the hallmarks of a fridge that may be overloaded with weight, on an uneven floor with misaligned levelling feet. Cut a piece of 1" marine plywood 1" bigger than the width and depth. Empty the freezer and put it on the plywood. Level the feet using a spirit level left to right and a fore and aft. Make sure it doesn't rock. Loosen the door hinges and centre the door. Fill the freezer back up.

Easy to measure the inside cavity and multiply it out but the FC **15** is 15 cubic feet.https://www.google.com/search?q=cubic+ft+is+my+freezer.+Model+no.+FFC15D9CW1&rlz=1C1QJDB_enCA643CA644&sourceid=chrome&ie=UTF-8..

Hello Michael - Sounds like the temperature control was accidently turned OFF. When this occurs the temperature control turns off the compressor, but does not disconnect the power to the light bulb or other electronics. Let's try activating the freezer by pressing the UP arrow until display shows "4" or desired setting. Allow 24 hours for temperature to stabilize. For future reference you can lock the control to keep from accidently changing the temperature setting. I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if the unit's status has changed successfully. Thank you.

Turn the temp down on the refrigerator side but not below freezing. Some frigs have a "trap" set up for the water dispenser. its located behind a panel in the frig and it is there to help chill the water before it dispenses. if the frig setting is too cold then it can freeze the water . If you need further help, reach me via phone at https://www.6ya.com/expert/steven_a67ead41eb5fc62a

in settings alarm might be turned off

Disconnect the power again for 5 minutes and then put a dinner knife across the two mains plug pins. Then plug it back in. If it doesn't work after that you need an engineer. The main board or other components may have been damaged by a power spike when the power cut.

you call a local repair service .

Correct whatever the code indicates and try again.

Or a control board problem

Thank you for your post, friend!

I see your Frigidaire refrigerator is not cooling and you have performed a reset on your appliance by unplugging it. You could be experiencing an issue within your control panel or sealed system. I would recommend seeking assistance from a professional to come and diagnose your appliance for the proper repair. Hopefully this is helpful. -Matt