2014 ford escape s oxygen sensor location
I am assuming yours is the four cylinder 2.5 litre engine. It will have 2 oxygen sensors. One will be near the engine before the catalytic converter, Either in the exhaust manifold or in the down pipe closest to it. That one is commonly referred to as the "Upstream" sensor. The OBD2 engine diagnostics will list it as "Bank One, Sensor One".
The second oxygen sensor is located just after the catalytic converter, often underneath the vehicle as the exhaust curls under the engine. This one is usually referred to as the "Downstream" sensor or "Bank One, Sensor Two" in the diagnostic system.
You can usually spot them easily as the stick out at 90' from the exhaust pipe with a thin wire coming out of it.
1978 ford f100 pickup truck won't move forward in drive why?
There are several possible causes of this issue. The first thing to do is to check if the transmission fluid is low. If the fluid level is low, it can indicate a leak or a problem within the transmission itself. You should also check the fluid pressure as well as the condition of the transmission filter and fluid. If the filter is clogged or if the fluid is contaminated or excessively worn, this could cause the transmission to not shift properly. It is also possible that the transmission linkage or the shift cable may be damaged or disconnected. Make sure to check the shift cable and linkage for any signs of wear, damage, or loose connections. If all of the above checks out, then it is possible that the transmission needs to be serviced or rebuilt.
My truck blows white smoke
Hello!
There are two differnt reasons for black and white smoke coming from the tail pipe.
Black smoke means fuel runs rich (car getting to much gas). Check fuel pressure/air filter.
In some cases the white smoke means car is burning oil or transmittion fluid. Have tem checked/replaced.
If you can feel a smelly smoke it can be catalytic converter.
In a worsest scenario if car blowing white smoke it can be engine coolant is getting into an engine cylinder from a bad head gasket ,or a warped/cracked head. So you need to keep your eye on coolant level and check your engine for overheat. Also might be good to check your oil for traces of coolant (on a dipstick it would be a milky substance mixture of oil and coolant).
Good Luck
2013 PX2 Ford Ranger shift lever adjustment ,have indefinite codes,,PO706 and 707
These codes refer to the sensor that reads which gear the transmission is in. The Transmission Range Sensor. The sensor is getting the wrong signal from the transmission. I'm not familiar with Rangers but there is usually a transmission 're-learn' trick that can reset the transmission to factory settings.
I don't know if this will work but it won't hurt the vehicle if you try it.
Turn the ignition to the second position, (Ignition On - Engine OFF). Wait for the dashboard lights to turn off.
Press the accelerator pedal all the way down as far as it will go and hold it there. Keep it pressed down for at least 30 seconds.
Keep the pedal pressed down and turn the ignition to the off position. DO NOT remove the key.
Do nothing else for 2 minutes.
After that remove the key, count to 10, then go for a drive. This should reset the transmission.
1979 Ford F100 how many gallon of gas I should put in the gas tank to start the engine?
for any vehicle on the market, its only necessary to put enough fuel in the tank to register movement of the fuel gauge.
if you have added enough to see it move just a little bit, that is plenty, if the vehicle does not start, begin test procedures to properly diagnose the reason it will not start.
just a gallon can make most move, but if you have put 3 or 4 gallons is and see no movement, check the gauge circuit including the new float and assembly You have just installed
2004 Ford Rocam Bantam burn fuse.
Question edited for clarity, correct model name rockem > Rocam
You need to identify the fuse and what is on that circuit and look for what is shorting it out. It is normally abraded insulation that is grounding back to the battery, or what is on the end of it has failed.
Ford Bantam (2002 -2011) - fuse box diagram
Auto Genius
https://www.autogenius.info > ford-bantam-2002-201...
Dec 27, 2015 - Ford Bantam (2002 - 2011) - fuse box diagram. Year of production: 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011. Central junction ...
Central Junction Box (Cjb)- Front View, Fuses - Ford 2002 ...
ManualsLib
https://www.manualslib.com > ... > Workshop manual
Ford 2002 Bantam Manual Online: Central Junction Box (Cjb)- Front View, Fuses. Item Description 1 Fuse F12 - multifunction switch, wind- shield wiper motor, ...
..
I need a diagram for
1999 Ford F Series Stereo Wiring
Constant 12V+
Light Green/Pink
Switched 12V+
Black/Purple
Ground
Black/Green
Illumination
Light Blue/Red
Dimmer
n/a
Amplifier Remote
Blue
Antenna
Right Front
Front Speakers
6" x 8" Doors
Left Front (+)
Gray/Light Blue
Left Front (-)
Tan/Yellow
Right Front (+)
White/Light Green
Right Front (-)
Dark Green/Orange
Rear Speakers
6" x 8" Rear Corners
Left Rear (+)
Orange/Light Green
Left Rear (-)
Light Blue/White
Right Rear (+)
Orange/Red
Right Rear (-)
Brown/Pink
Not finding what you are looking for?