Dremel Tools & Hardware - Others - Recent Questions, Troubleshooting & Support

Question edited for clarity. Question moved from Televisions. https://www.google.com/search?q=hyper+tough+rotary+tool+won%27t+turn+on

I'm sorry, but I don't have access to specific service manuals for individual tools. However, here are some steps you can follow to find a service manual for your Weller Mini Shop Model 601 Dremel tool:

1. Visit the Weller website: The Weller website may have a library of manuals for its products, including the Mini Shop Model 601.
2. Check the manufacturer's support page: Most manufacturers have a support page on their website where you can find user manuals, FAQs, and other resources.
3. Search online: You can also try searching online for a digital copy of the manual. Websites like ManualsLib and ManualsOnline may have the manual you need.
4. Contact the manufacturer: If you're unable to find the manual online, you can contact the manufacturer directly and request a copy. You may need to provide your tool's model number and other information.

I hope this helps you find the service manual for your Weller Mini Shop Model 601 Dremel tool.

Question edited for clarity. Question moved from Rotary Club International :>D Dremel don't make Craftsman Rotary Tools https://www.google.com/search?q=does+dremel+make+craftsman+rotary+tool& Decide if you have a Dremel or a Craftsman and Google simply make model parts ..

Question edited for clarity, spelling of Dremel. Question moved from Cameras Category. How to strip and replace the locks. https://www.google.com/search?q=Dremel+4200+and+the+blue+unlock+tabs+are+stuck+on+unlock ..

You'll need to use either the built in shaft lock to hold the collet in a fixed position, or use a pair of slip joint pliers to hold the shaft of the bit, while you use the wrench to loosen the collet. Slow and steady should get it loose. Another option is use some penetrating oil sprayed lightly onto the back of the collet to help loosen it from the shaft etc.

Question moved from Cars and Trucks There are a few parts here https://www.ereplacementparts.com/dremel-1731-f013173100-benchtop-belt-sander-parts-c-15440_15441_15442.html You may be able to get pulleys made using the bearing from yours which can be pressed out. Or you can get your pulleys sleeved. Other parts suppliers https://www.google.com/search?q=dremel+belt+sander+730+parts ..

Model of dremel, battery or mains powered?

Try using the correct collet size

This can happen if you accidentally depress the spindle locking button while the tool is running -- a common problem since Dremel did not include any type of interlock to prevent it, and the button is right where you'd hold the tool for best control. If that happens, you probably will need to replace the tool or send it to Dremel for repair.

My stylus is doing exactly the same thing. l was advised by numerous people to change the capacitor in the charging dock, they also said that you can find youtube videos to guide you through it (the capacitor only cost a few cents when l bought it). I really should finish doing that job, although l did actually remove the 'screws'' from the base, l warn you- they are triangle and a nightmare to unscrew, see if you can find a triangle screwdriver BEFORE you start, or you'll end up doing what l did and destroying a perfectly good straight screwdriver!??. Good luck

Change tha capacitor 220uF and it will probably be fine! I did and now it is as new!

Question edited for clarity to add Maker. Question moved to Make Model category. The lock button should lock the shaft. With the collet facing you, turn anti-clockwise with grips or pliers. They should never be done up _that_ tight. Try spraying with penetrating oil. Two version of the manual below.

DREMEL OF Multi 395

https://docs.rs-online.com > ... PDF the better products of its kind. • To get the optimum benefit from the tool we advise you to read this instruction manual thoroughly.

DREMEL Moto-Tool Owner's Manual

https://neurophysics.ucsd.edu > Manuals > Dremel PDF DREMEL. Moto-Tool Owner's Manual. Models 275, 285, 395, and 595. 3. HONESTLY NOW... Have you read this. OWNER'S MANUAL? This manual will tell you how to get ... 11 pages

I have exactly the same unit a 395. The kit comes w/ a wrench to unscrew the nut holding whatever you have locked in. If you can't find the wrench then I suggest you get an adjustable wrench and lock it into the flat side of the nut. There is a place where it will lock in so that you can tighten or loosen the nut. Some of the 395's come as a kit w/ all the different attachments, accessories, heads and tools. If it came with a plastic case the wrench is usually slotted running parallel just in front of the handle. You will see it when you open the case and take a top view look at the handle. It is sometime hard to see but it's just there. Good luck.

Here's the email from I got from Dremel (in my case the flex coupling broke):
Inside the tool is a flex coupling and spline driver.

The flex coupling is # 2615294309 and the price is $ 1.25.
This is the hollow plastic sleeve about 1" long with grooves on the
inside, that goes between the motor shaft and the output shaft.

The spline driver is # 2615294308 at $ 1.00.
Spline driver sits on the direct end of the motor shaft. The flex
coupling sits over the spline driver. Spline driver is about 1/4",
hard plastic with grooves on the outside.


Total shipping for orders under $ 5.00 is $ 2.50. Orders over $
5.00 is $ 4.00.


I have provided ordering instructions below.

To order by phone: 1-800-437-3635, Monday-Friday from 7 am to 6 pm
central time. VISA, MasterCard or Discover is accepted.

To order by mail:
Dremel
4915 21st Street
Racine WI 53406

My motor was turning but the flex shaft wouldn't. I took the flex shaft loose and spun it inside. Works fine now.

This is the charger, its getting a reading from the battery that its charged when it isn't. I don't know exactly how that charger is wired but, to be suroe it is the charger, as I have had similar problems beforehand.

Look at the clogged teeth on the blade. Copper does that. Use a pair of tin snips.

hello. yes. go to dremel.com and get new brushes for your tool.
ps kindly rate my answer as helpful. thank you. Joe

There is a coupling between the drive motor and the chuck. You will need to take the tool apart to replace it. E-bay has these.

It will be under warranty if just bought it , if faulty it will be repaired or replaced at no cost to you .