Delta Cutter Tools - Recent Questions, Troubleshooting & Support

Operator's manual for the 22-547 is here.

It sounds like you may need to adjust the knives. Page 10 and 11 of the operator's manual discuss the details. See below: (I have removede references to the figure and diagrams in the manual - look there for pictures).

ADJUSTING KNIVES

To check and adjust the knives, proceed as follows:
1. DISCONNECT THE TOOL FROM THE POWER SOURCE.

2. Lower the head assembly by turning handle

3. Remove chip deflector

4. Carefully place knife setting gage, on the cutterhead so the rounded sections are directly over the knife as shown. When adjusted correctly, the knife should just contact the bottom of the center portion at each end of gage. Check the other knife in the same manner.

5. If an adjustment to one or both knives is necessary, slightly loosen the seven locking screws, by turning the screws CLOCKWISE into the knife locking bar just enough to relieve stress in the cutterhead and not disturb the knife setting.

6. With setting gage, in place, apply pressure to the knife being reset. Turn the seven knife locking screws, CLOCKWISE until the knife locking bar becomes loose. Lift springs will automatically raise the knife until it comes in contact with gage. Snug the knife locking bar by lightly turning the seven locking screws, COUNTERCLOCKWISE.

IMPORTANT: AT THIS TIME, ONLY TIGHTEN THE KNIFE LOCKING BAR JUST ENOUGH TO HOLD THE KNIFE IN POSITON INSIDE THE CUTTERHEAD SLOT.

7. If the other knife needs adjustment, repeat STEP 6.

8. After both knives are positioned in the cutterhead, turn each of the seven screws, COUNTERCLOCKWISE until the knife is secure in the cutterhead. NOTE: When tightening knife locking screws, tighten the end screws first, then inward toward the center of the cutterhead.

9. Replace chip deflector.

Exploded diagram is here.
Operator's manual is here.

If this answer was useful, please vote. Thanks.

go to Dewaltservicenet.com and type in your model number and you can download a users manual for this tool the pages you need are 10 and 11. Let me know if you need more assistance and if I have helped you would you please rate this response accordingly.

If there is you would find it at Dewaltservicenet.com and in the middle of the page under manual type in your model number for a schematic and owners manual for the tool.

go here to aquire your manual:

http://www.deltaportercable.com/ServiceAndSupport/OwnersManuals.aspx

Go to Dewaltservicenet.com and in the middle of the page at the bottom type in your model number on the next page click on the model on the left hand side and they when you get to the breakdown look for instructions manual, I generally have to click 2 times to open it up, after first click the box will go away just move your mouse and left click and it will come back and then click on it again. Go to page 11 of the instruction manual. If I have solved your problem would you please rate my response accordingly. Thank you

Go to Dewaltservicenet.com and type in your model number in the middle of the page at the bottom. Select the model number I looked at a type 2 and click on it on the next page find instruction manual on the left hand side and I did have to click 2 times before it brought it up but it is there I just read part of it. The manual is about 17 pages long but the page you need is 11. Let me know if there are any problems please and if I have helped in anyway would you please rate the response accordingly.

copy and paste link https://www.manualslib.com/manual/97951/Makita-Dpc-6400-Dpc-6401-Dpc-7300-Dpc-7301.html?page=17

Hi, please replace the batteries first. If that does not work, please attempt to factory reset your device ( can reference manual). Thank you.

A pipe cutter is a tool that plumbers use to cut pipes. It gives a much cleaner and better cut than saws.

check base groove for debris / damage

Question edited to fix spelling. It is a Utility Knife, it has no software downloads. You posted to Computers and Internet? I'll move it to Cutting Tools. https://www.google.com/search?q=stanley+10-778

6-5/8 in FATMAX® Retractable Utility Knife ' STANLEY

https://www.stanleytools.com > product > 10-778 > 6-5... Designed with the user in mind, the 6-5/8 in. FATMAX® Retractable Utility Knife offers durability and strength in one compact package. .. .

You should wear gloves to protect your hands from slips and goggles or face mask to protect your eyes and face from any metal pieces that may come off the bolt you are cutting.

Request the manual from the manufacturer/distributor.

With the cheapest multimeters costing as little as just a few dollars there is no reason not to have the ability to check things instead of guessing. With most portable tools and appliances the first thing to check is the power cord because around 60% of the time an internal break is the cause of a tool not starting. Power tools and appliances often have electronics to provide variable speed or soft start. Checking these is beyond the scope of the home repairer but a multimeter can check continuity to any electronic component and from it to the motor and the ensure there is continuity through the motor. If everything else is ok the fault is probably with the electronics if there is any. If you are feeling really brave, the final test is to temporarily and safely bypass the suspected component and apply power.

you can use a portable bandsaw to cut rebar, I find it to be the best solution when I can't take the rebar somewhere to cut it. But be careful if the metal is heavy it could fall and dent/damage the floor if you're working indoors of cause injury should it land on you.

Use a third blade, preferable mounted to your utility handle, to part them. Handle only from the back side and give the utility knife a slight twist as soon as it is between the points of the new blades.