CDA Cooktops - Recent Questions, Troubleshooting & Support

https://www.cda.eu/connector/downloads/manual/4899/HN9610_im.pdf https://www.cda.eu/download-user-manuals

IS THE POWER TO THE HOB ON ? IF SO IS THE FUSE OK ? IS THE PLUG WIRED CORRECTLY ? TRY THESE FIRST, IF NO JOY YOU CAN DOWNLOAD YOUR PRODUCT GUIDE FROM CDA ON LINE

1: isolate the electricity supply to the cooktop2: take the knobs off, and check there isn't any contaminate or oil liquid under the knobs.3: feel for the correct action of the pushbutton under the knobs.4: call the service agent....

There is a little hole under the tray towards the right hand side. Straighten out a paper clip and push it carefully into that hole and the tray should unclip and pop out a short way.

try getting it resurfaced places like game stop or most electonic game dealers do this for a charge of around 8 dollars

if you need a manual visis www.cda.eu and you can download one from their

probably gummed up from oil and grease if u have access to the motor use a spray lube and spray the shaft as it goes into the motor case this should free up the bearings -if no access remove motor clean than oil up motor turn motor back and forth by hand and will free up replace and test

The ER42 error code typically indicates an issue related to insufficient power being delivered to the ceramic element. Check Power Supply: Ensure that the cooktop is receiving adequate power. Verify that the power supply is stable and not fluctuating. Inspect the PCB (Printed Circuit Board): Since the error points to a fault on the PCB, visually inspect the control board for any signs of damage, loose connections, or burnt components. Capacitors: You mentioned that you've already changed the capacitors. While this is a good step, it's essential to ensure that the new capacitors are correctly installed with the same rating and polarity. Reset the Cooktop: Turn off the power to the cooktop completely. Disconnect it from the mains for a few minutes, then reconnect it and power it back on. Sometimes, a reset can clear minor glitches. No joy? Consider professional repair.

It needs a new control if it has dials or a control pad or a part if it is electronic. Full make and MODEL (what it is) in all answer please as first 3 words in every question.Edited as model number given Whirlpool GFE471LVShttps://www.whirlpool.com/owners-center-pdp.GFE471LVS.htmlThe Infinite Switches are $130, so it is best to test them with a multimeter first.https://www.partswarehouse.com/Whirlpool-GFE471LVS0-Freestanding-Electric-Range-s/131742.htmVideos showing how to changehttps://www.google.com/search?q=whirlpool+gfe471lvs+replace+hob+infinite+switchOwner Manual, just because it was therehttps://www.manualslib.com/products/Whirlpool-Gfe471lvs0-10479409.html..

Child Lock function is on. https://www.google.com/search?q=Beko+H1164403T+induction+hob+child+lock ..

A) https://hobguide.com/induction-hob-cannot-detect-pan/ B) https://hobguide.com/induction-hob-not-working-on-one-side/ You are advised to not try to get into the electronics of the induction hob. Such is dangerous. The unit uses 3 phase electricity, something unlikely to be addressed by DIY activity if you want to be safe. Check your warranty. I assume this is not a matter of pans of the wrong material or size being deployed. This well may require a technician to sort out. The brand/model has not been identified so I cannot direct you to further resources. Your user manual surely provides a company name where you might seek some customer support.

There seems to be quite a few ways... Check out these sites.. https://www.google.com/search?q=How+can+i+remove+a+stuck+venturi Best to you.

Based on the symptoms described, it is possible that the issue lies with the ceramic element that the burners connect to at the back of the burner unit. This could be causing a short circuit between the two burners, which is preventing the large burner from being adjusted lower when both burners are on. It is also possible that there is an issue with the wiring or connections between the two burners, which is causing a similar short circuit. However, given that the smaller burner appears to be working fine, this seems less likely. Another potential cause of this issue could be a problem with the control board or another component of the stove's electrical system. However, given that replacing the infinite switch and receptacle for the large burner did not resolve the issue, it seems less likely that this is the root cause. In order to determine the exact cause of this issue, it may be necessary to consult with a professional appliance repair technician who can diagnose and repair the stove.

If your ceramic cooktop model CEC70 is not turning off, there are a few steps you can take to troubleshoot the issue: 1. Check the controls: Ensure that you have properly followed the instructions to turn off the cooktop. Some models may require you to press and hold a specific button or combination of buttons to power off the cooktop. Refer to the user manual for your specific model for detailed instructions on turning it off. 2. Power cycling: Try power cycling the cooktop by turning off the power at the circuit breaker or unplugging it from the power source. Leave it unplugged or with the power off for a few minutes before plugging it back in or turning the power back on. This can sometimes help reset the controls and resolve any temporary issues. 3. Control lock: Check if the cooktop has a control lock feature that might be activated. Some models have a lock function to prevent accidental changes to the settings. Look for a button or key combination that activates or deactivates the control lock. Refer to the user manual for instructions specific to your model. 4. Contact customer support: If the issue persists, it is recommended to reach out to the manufacturer's customer support or consult a professional technician who specializes in appliance repairs. They will be able to provide further guidance or arrange for a service visit to diagnose and fix the problem. Remember, when dealing with electrical appliances, it's always important to prioritize safety. If you encounter any unusual or potentially hazardous situations, such as smoke, sparks, or strong odors, immediately turn off the power supply and contact a professional technician for assistance.