Candy Washing Machines - Recent Questions, Troubleshooting & Support

Candy Washing Machine

1. Push and hold the FIRST Option Button with LED top right.
2. Turn the Program's Selector Knob 2 clicks clockwise.
3. After about 5 seconds, release the FIRST Option Button.
4. If the previous procedure was correctly carried out, all LEDs are turned ON simultaneously.
5. Press the START/PAUSE Button to start the self test mode

the pump is blocked up or the filter once you take the blockage you need to reset the machine too do this turn off the mains power press and hold usually the start pause or menu button and turn the mains on wait a few seconds and let go should clear the fault detection if it is the filter or a blocked bad pump and its clear then the machine will reset

Error code E11?? See error codes here: How to Understand Hoover and Candy Washing Machine Error Codes

https://www.youtube.com/watch?v=-Ugge61yrHE Has to do with the motor

I have always found that my Candy refuses to function at times, especially if I have tried to set it with wet hands. Do a Master Reset. Switch the circuit breaker off. Wait for 60 seconds. Turn it back on. Open and close the door 6 times within 12 seconds. I know it sounds mad but it works.

Check all the connectors on the control board and display board. Undo, spray with switch cleaner and replace.

It sounds like there may be a problem with the control board or circuitry in your Candy Grand Evo 8123D washing machine. The ticking noise could be an indicator of a fault in the machine's control system. To troubleshoot the issue, you could try the following steps: Unplug the machine from the power outlet for a few minutes, and then plug it back in. This may reset the control board and solve the problem. Check the power supply to the machine. Make sure that the power outlet is working and the machine is receiving the proper voltage. Check the door lock. If the door is not properly closed or the lock is faulty, the machine may not start. Check the machine's control board and wiring for any signs of damage or corrosion. If none of these steps work, it may be best to call a professional appliance repair technician to diagnose and fix the issue

The error code you are seeing on your Candy Bianca washing machine indicates a problem with the water supply. Here are some steps you can take to try and resolve the issue:

1. Check the water supply: Make sure that the water supply to the washing machine is turned on and that there are no issues with the water pressure.
2. Check the water inlet hose: Make sure that the water inlet hose is not kinked, twisted or damaged in any way. Also check that the filter at the end of the hose is not clogged with debris.
3. Check the water inlet valve: The water inlet valve may be faulty and need to be replaced. You can test the valve with a multimeter to check for continuity.
4. Check the water pressure sensor: The water pressure sensor may be faulty and need to be replaced. You can test the sensor with a multimeter to check for continuity.

If you have tried all these steps and the problem still persists, it may be best to contact a professional appliance repair technician for further assistance.

They are all listed here. https://www.google.com/search?q=candy+washing+machine+agent+in+Sri+lanka ..

I ordered same unit. Came to me with motor spinning backward. Was wired incorrectly. When I fixed the wiring started making perfect floss.

Did you wait a few minutes with the plug out? Resetting your washing machine

• First, you should perform a general reset of the machine. Turn the machine off at the powerpoint, wait for one minute, and then turn it back on.
• If you see no change, you can try a Master Reset. This will reset all of the onboard componentry and is often successfully used by appliance technicians. Open and close the door of the washing machine 6 times within 12 seconds. Then, run the rinse/spin cycle without clothing to see if your problems are resolved.

Videos https://www.google.com/search?safe=off&rlz=1C1QJDB_enCA643CA644&sxsrf=ALeKk02EhTBpcI120j_WFsU5-v4VX0gGEg%3A1613427360420&ei=oPIqYIjvGLri5NoP4MGDmAE&q=candy+bianca+washing+machine+reset ..

QuietGuard3: Firstly, Clean light flashing 7 times? Secondly, Press Heated Dry, press Normal Wash, then press Heated Dry again Lastly, press Normal Wash again (that's 4 button-presses) and that should fix it.

Yes, this is normal, and you need to clean it out regularly, or the machine will stop working.

Turn the machine on with dry hands. If it still won't start, unplug it or turn the circuit breaker off, then back on until the breaker firmly clicks in place and plug the machine into the outlet. Push the restart button. Some machines may require you set the knob to a specific setting for the reset feature to work. https://homeguides.sfgate.com/reset-buttons-washing-machines-104441.html

Question edited for clarity and spelling of 'machine'. That sounds a bit like a delay timer. Try pressing the Pause button ONCE. Don't press it twice for good luck! You can also try disconnecting from the mains overnight to reset the control board. Manual doesn't show a 'display panel'. https://www.manualslib.com/manual/806797/Candy-Alise.html?page=4#manual ..

If it is only doing it on the drying cycle, it must be the forced air fan that blows the heated air through the clothes. For dryers that have sensors, the time will often go up as the sensor realizes the clothes are wetter than it first thought. Once it reaches a sound judgement, it should start to decrease. If it doesn't, you have sensor or control board issues and you need a service visit. You can Google make model parts schematic and see all the parts and the costs. Control boards are very expensive.