Candy Dryers - Recent Questions, Troubleshooting & Support

Check your belts and see if they are broken. Your blower may not be running. With no blower there will be no air flow there for not drying.

Look at the back of the condenser. It has a plastic cover. The plastic at the bottom has most likely become warped preventing the condense being pushed back in to place. How do I know that? because it happened to mine

The breaker box in the unit may not have the rated breaker for your appliance. Most likely. Have them check it out.

Using only the information I read, it sounds like the drum is not turning. This might be from a broken drive belt. It could also be from an overheated thermostat and/or a blown internal fuse. Have a mechanic or technician take the machine apart and find out the problem God bless your efforts.

The E22 error code on your Candy Condenser Tumble Dryer model GVS C9DCG-80 31100907 indicates a problem with the drainage system. This could be caused by a few different things:

1. Blocked drain pump: The drain pump may be clogged with lint or debris, preventing it from properly draining the water from the dryer. Check the drain pump and make sure it is not blocked.
2. Drain hose: The drain hose that carries the water from the dryer to the drain may be clogged or kinked. Check the drain hose to make sure that it is not blocked or kinked.
3. Drain filter: Make sure that the drain filter is clean and not clogged.
4. Control board: The control board manages the dryer's functions and if it's faulty it can cause the E22 error.

To reset the error code E22 on your model, unfortunately, it seems that your model doesn't have a reset button or an option button to reset it. The best course of action would be to contact the manufacturer or an authorized technician for further assistance on how to reset the code and troubleshoot the problem. They will be able to diagnose the problem and provide you with a solution.

Csoe C9ocg 80 all lights flashing my dryer is outside in shed

Lots of ideas here. It is bound to be some type of thermal cut out. If the clothes are hot, it is the drum thermal cut out. If the clothes are only warm, it is the motor protecting itself from fire. When was the last time it was completely stripped and cleaned out? https://www.google.com/search?q=Candy+Smart+tumble+dryer+stops+after+2+minutes ..

Question edited for clarity. Unlikely to be the control switch and more likely the Humidistat Control Sensor that decides if the clothes are dry or not. It is a very complicated dryer. https://www.manualslib.com/manual/976997/Candy-Gcc-590nb.html?page=7#manual ..

If you really have 252 volts, you need to contact your electricity utility company. If you are in the UK (fuse in plug clue), you should have 225 to 230. 230 volts Although the normal voltage in the UK is 230 volts, it is not constant. The voltage at your property will vary due to the use of power and normal operation of the power supply network. Our network is designed to ensure that the voltage stays within the permitted tolerance or statutory limits.

Voltage Changes - SP Energy Networks

If you use fabric softener, you can bet on it.

It doesn't generate fluff, it uses evaporation to dry the clothes. If it did, that instruction would be in your user manual.

nope other than calling a local repair service

Slot online sangat bermanfaat untuk memperoleh kemenangan hingga ratusan juta rupiah. silakan bergabungan bersama kami untuk keberuntungan anda di link ini. http://149.28.158.118/

ELECTRICDryer no heat or little heat, or shuts down to fast: Checkyour venting and lint basket. Check blower for lint build up and blower wheel obstruction., test by trying to turn the wheel manually by hand (should be easy) May have to remove cabinet or front/back plate to get to it) Next check the heating element itself with a meter for continuityit should showOHMS CLOSED CIRCUIT. If not its defectiveor has a short if its grounding out? Which in turns causes blown fuses or thermostats or overheating. The heating elements are located inside the heater ducts. If you think a heating element is faulty, test it with avolt-ohm-multimeter(VOM)set to the RX1 scaleat 20K ohms. Disconnect the leads from the power terminals and clip one probe of the VOM to each terminal. The meter should read about 12. (1200)ohms.If the reading is higherohms, the heater is faulty and should be replaced. Replace a faulty heater with a new one of the same type and electrical rating. A heater connected to a 115-volt line usually has an 8.4-ohm resistance; a heater connected to a 220-volt line usually has 11 ohms resistance. Check dryer Terminal block prongs both outside prongs should give combined 220, and 110 each if u check 1 outside & 1 center (ground) prong. Also check house electrical outlet for full voltage. 220 because if u only get half or 110 volts you will be able to run the machine which uses only 110 to run motor but not the heater which uses a full 220,OR?you may have a broken centrifugal switch in the motor because this switch activates the motor and the heater as well. supposedto be if the motor does not run, the heater should not heat in order not to createafire but ifthe motor is not running,andthe heater is still heating, then there could be a problem with the motor centrifugal switch that is connected to this interlock switch that should trigger the heater. Check the thermal cut off, the cycling and the hi limit thermostats. For continuity or OHMS. If no ohms or resistance they need replacement. In somedryer'sthecontrol panel relies on athermistorrather than aCYCLING thermostatto regulate the drum's air temperature by monitoring the component's resistance changes; resistance goes down as temperature increases and up when temperature decreases. Once the drum's air temperature reaches a certain level required to dry clothes, the control panel shuts off the heater. The panel will turn the heater on again and begin another heating cycle when thethermistorindicates that more heat is needed to keep the air temperature constant inside the drumthis is why in some cases the dryer will operate at lower cycles like gentle or low heat but not at higher settings?) Lastly check your moister sensor.( located inside the dryer door usually) Especially if machine seems to shutdown early and clothesare still wet. Test with a meterat room temperatureand it should show continuity. A failed moisture sensor will affect the dryer run timein the automatic moisture sensing cyclebut it will not affect the heatingof the dryer or the timed cycle.Which are reflected by the thermostats. Read more : https://www.youtube.com/watch?v=wVTBrGMql7g http://www.ehow.com/info_12203962_check-dryer-thermistor. GOD IS So GOOD !!!!AND THAT'S WHY MY ADVICE IS FREE https://www.youtube.com/watch?v=MMP7BW1lLs4

Dryer Repair Help How to Repair Your Dryer Clothes Dryer Repair Guide there are several sites for troubleshooting and repairing dryers just Google it.

i don't know and don't know your dryer. some dryers have a safety pointer on the door so it will not run. it could be the switch the pointer pushes on. if pin is not quite touching safety switch, dryer will not turn on. be careful and don't by pass this switch. if you think this could be the problem - first try pushing on door to see if dryer runs. if not, you could use a thin stick to push in hole with door open. if it turns it has become loose and needs to be reinstalled. if it does not turn the switch should be checked with an electric test meter for continuity.

i don't know. please check the home's fuses or reset the electrical panel's circuit breakers.

Hi i have my dryer for under 12 mouths it all works comes on for a bit then starts to bleeping and it says e15 and then cuts out does the dryer have a rest button on it thanks