Water Filters & Coolers - Page 5 - Recent Questions, Troubleshooting & Support

The one I made a change, it was like a rubber cork that you just pull out and a push new one in. Hope this helps.

The control board is 860-3.30 the other part you listed is a cover. The item is made by greenway home products. Try to contact them because they dont show that part and that model was 7 years old. https://shopca.greenwayhp.com/index.php?main_page=index&cPath=87&sort=20a&page=2

Do just what you did to ask this question.

Is there a filter between supply and the Hot water heater? The heater may be similar to Coffey pots. a small tube. I would try to deliver vinegar to the water supply before the heater a good long soak may help. It may also be a problem with the dispenser valve, depending on where it is and whether its manual or electrical. It may be blocked. Hopefully, the vinegar might clean. Otherwise. if manual try to disassemble inspect find the problem. It may need a replacement rubber seat kind of like old faucets. If it's electrical, there may be a problem with the connection, but most likely it will be similar to dishwasher or chloths washer valves. and need to be replaced with a complete module. Its possible there is a fine protective screen at the entrance from supply to electric valve. If plugged the screen should be able to be removed and cleaned. Hope this helps and good luck.

Have you changed the intake filter or pipes in any way, too much air could be drawn into engine, check ports, jets and float valve, adjust mixture screw to 4 turns out then adjust by ear half turns either way, check fuel pump return.

The thermostat has become defective or it has lost freon or the compressor has failed.

Unless it is the thermostat, It may not be cost effective to repair so check the cost of a replacement.

That unit uses Peltier thermo electric cooling devices. They are not expensive. http://www.wisegeek.org/what-is-the-peltier-effect.htm

Make sure that all valves are in the open position.
Try to recharge the water storage tank. Here are the steps to follow.
* In General: When any type shut-off valve handle is positioned so that it is parallel or in line with the tubing that enters the valve, valve is OPEN. When handle is turned perpendicular to tubing that enters valve, valve is CLOSED.

Necessary Supplies:
1) Tire Gauge marked in 5psi increments (ie 5, 10, 15, 20psi, etc.)
2) Bicycle tire pump for standard type bike tire valve
To recharge RO system tank:

1) Close cold water feed valve (valve located at some point along the cold water line from street plumbing).*
2) Leaving RO tank valve on, turn tank on side & locate valve stem on bottom side.
3) Remove stem cap.
4) Drain all water out of tank through open RO faucet into sink. (Continue to leave RO faucet open throughout procedure)
5) If current tank pressure is insufficient to empty tank, apply tire pump to valve stem and pump 10 – 15 times. Exit flow will increase and then gradually decrease as pressure equalizes. Do not overcharge internal bladder of tank during this
procedure.
6) Repeat step #4 until tank is completely empty. (Tank is empty when additional pumping produces no more water)
7) At this point, adjust EMPTY tank to exactly 7psi. (Gauge reading midway between 5 & 10psi is sufficient)
8) Turn off RO faucet.
9) Replace cap on valve stem and reposition tank in upright position.
10) Open cold water feed valve.*
11) System water is useable immediately, however, tank will take 3-4 hrs to completely refill.

www.FreshWaterSystems.com: The Water Super Store: 1-877-335-3339

If you want the reverse osmosis water to go to the ice maker then you tap in to the line that feeds the spiget on the sink.

Unfortunately you have not given many details including what brand and model it is but sometimes this can be a clogged filter but may also be a different issue

Hi, It is dues to improper air flow. which can be caused by multiple factors. 1. Return Air Vent is blocked 2. Evaporator Fan not working 3. Improper Thermostat. Is the water cooling Ok. if the thermostat is not ok, the water might be really freezing.

A bad thermostat .

Try to find them here Find the low cost Wholesalers Dropshippers on biggest wholesale place. Best of luck

HI.UMMM WELL i would think is not a problem but normally tap water has fluoride and clorine which gives a bitter tate and cloudy water.sooooou. u make your mind up...plus the ready bottle is sealed as well as one way ticket in and out.good luck hope this helps ali

yes you answered your questions there. i researched info and more than likely it is the valve http://watersoftenernews.blogspot.com/2014/02/culligan-water-softener-noise.html

I really need more info about you problem....

Having same issue. Water cooler about a week old, in use in a small office with about 10 people and 2 5-gal water jugs consumed weekly.

The chiller for the cold water no longer works, and they display lights on the front and on/off switch in the back no longer light up. The hot water is working, I'm wondering if there is a potential recall issue with the unit.

If by coolant you mean freon, and if by motor you mean compressor, then no, you can not do it without special equipment. It requires a technician. Usually cheaper to replace the water cooler.

Your thermostat is set to cold or is stuck in the on position, replace or turn it down