Question edited for clarity.
'then', a moment in time.
'than', a comparison between one thing and another.
It depends on the model, but usually related to the lid lock. Also check the breaker.
Why does my washer stop working after filling with water?
If the Top Load Washer stops after filling with water, be sure to check the house circuit breaker/fuse as well as the outlet and plug. Washers should be plugged into their own separate, dedicated outlet.
..
The A13 error on a Realstar dry cleaning machine R325 indicates a problem with the machine's solvent level sensor. To fix this error, follow these steps:
Check the solvent level: Ensure that the solvent level in the machine's tank meets the required level.
Inspect the solvent level sensor: Examine the sensor for any damage or obstruction.
Clean the sensor and its surroundings: Remove any dirt or debris that may be affecting the sensor's performance.
By following these steps, you should be able to resolve the A13 error and get your Realstar dry cleaning machine back in working order!
Is the correct tension on the belt; too much and the bearing could be getting damaged.
If you remove the belt, check the drum moves freely with no noise. If noisy, replace the bearing or purchase a new machine.
Leveling: Ensure the washer is properly leveled. An unbalanced load can trigger the UL (unbalanced load) code. Use a level to check if the machine is sitting evenly on the floor.
Load Distribution: Make sure the clothes are evenly distributed in the drum. An imbalanced load can cause the UL code to appear.
Calibration: Some models have a calibration mode that can be accessed through the control panel. Running a calibration cycle might help the washer to detect load balance more accurately.
Electronics: There could be an issue with the control board or wiring harness. Inspect these components for any visible damage or loose connections.
Professional Service: If none of the above steps resolve the issue, it may be time to consult with a professional appliance repair technician who can diagnose and fix the problem more accurately. They may have specialized tools and knowledge to pinpoint the exact cause of the UL code.
Usually it's the lid switch..When you open the lip look straight down usually..When you close the lid it inserts a small plastic piece that goes into the hole telling the washer the lids down..If it broke it will make the washer stop mid cycle..You can stick a wooden (only made of wood) into the hole and sometimes it will start to work..Then you know that's the problem and just get your model number of the washer and replace it..Hope this helps
This is a question that is hard to answer without a make and model or where a picture is worth a thousand words. It is a two tap mixer, it is the O-ring at the base of the swivel neck.
Individual taps leak from the cartridge or the gland packing just below the handle.
O c?digo de erro E5053 em um carregador L538 geralmente est? associado a problemas espec?ficos ou falhas no equipamento. No entanto, sem mais informa??es sobre o contexto ou o fabricante do carregador L538, ? dif?cil fornecer uma resposta precisa sobre o significado exato desse c?digo de erro.
A melhor abordagem seria consultar o manual do produto fornecido pelo fabricante do carregador. O manual geralmente cont?m informa??es detalhadas sobre c?digos de erros espec?ficos, suas causas potenciais e procedimentos recomendados para solu??o de problemas.
Se voc? n?o tiver acesso ao manual do usu?rio, pode ser ?til entrar em contato diretamente com o suporte t?cnico do fabricante do carregador. Eles devem ser capazes de fornecer assist?ncia espec?fica com base no c?digo de erro que voc? est? enfrentando.
The L221 code on a Linde H20 forklift indicates a hydraulic fault, specifically related to the tilt pot.
L: This letter signifies a hydraulic issue.
221: Refers to a faulty tilt pot.
Here are some potential troubleshooting steps to address this issue:
Check the Tilt Pot Connection: Depending on the year of your forklift, the tilt pot's plug might have a poor connection. If it's an older model with a non-waterproof plug, moisture could be affecting it. Try unplugging it and cleaning it thoroughly with electric cleaner.
Inspect Wiring and Linkages: Verify that the wiring is intact and that the linkages are not worn. If everything seems fine, you may need to replace the tilt pot. Keep in mind that recalibration using a laptop might be necessary. Display Code L221 - Technical Troubleshooting discussion in Forkliftaction's forums
Stale smells come from not drying the front gasket trough just inside the door. Your bleach isn't cleaning that area. Use Tilex Mold spray on it. Clean and dry the door glass as well and leave the door open for a few hours after a wash or leave it open all the time. If it is dry, it can't smell.There will always be some water in the pump area, but if you remove the pump filter cover, that releases and water left behind.When you use bleach always do whites or your tea towels next. You can also dilute by adding a couple of jugs of water first.There is a trick to look for rattling items between the inner and outer drum. Put a good flashlight against the holes in the drum and you can see what is below without getting the glare from the drum.These websites give you a full parts schematic showing all the parts and their positions.https://www.appliancepartspros.com/tub-basket-parts-for-whirlpool-wfw94heaw0.htmlWhirlpool Washer WFW94HEAW0 - OEM Parts & Repair Helppartselect.cahttps://www.partselect.caCanada Wide Same-Day Shipping For All In-Stock Parts. Shop Canadian And Avoid Customs ' 2 Million Parts Ready To Ship. OEM Parts & Accessories. One-Year Warranty. Money Back Guarantee. Free Repair Help & Videos. Types: Dishwasher Parts, Dryer Parts.
Yes just disconnect it from the mains supply and leave it overnight. It will lose its stored memory.
Or from Model EW-824 Manual
Press this button to select once of the four positions, then select the additional options for your favorite washing cycles, then press Start/Pause button to run this program, and this program will be memorized. If you want to run the memorized program later, press this button to select one of them, then press Start/Pause button.
Turn the dial to align "OFF" to cancel the memory operation
https://www.google.com/search?q=Equator+835+clear+memory
Manual for model 835 at memory page
https://www.manualslib.com/manual/2389625/Equator-Super-Washer.html?page=17&term=memory&selected=1#manual
Press this button to select one of the four memory settings. Then select the your favorite Memory button wash cycles. Then press START/PAUSE button to run this program, and this program will be memorized. If you want to run the memorized program later, press this button to select
desired program and then press START/PAUSE button
..
Repair Clinichttps://www.repairclinic.com > RepairHelp > Electrolu...
Here are the most common reasons your Electrolux washing machine is leaking water - and the parts & instructions to fix the problem yourself.
..
Slip a sheet of newspaper under the bottom of the machine and it will indicate the area. If is does it when the machine is not running. My guess is that it is around the pump because some water always sits there, so either the pump body or the drain hose itself.
