Washing Machines - Page 3 - Recent Questions, Troubleshooting & Support

If your IG Ignis 105 LA washing machine does not show any lights after a low voltage run and power surge, check the power supply, main control board, and internal fuses for damage. Consider contacting IG Ignis customer support for remote troubleshooting guidance or arranging for a technician to inspect and repair the appliance.Hi Tracey and welcome to JA, sorry for the delayed response, flat out all day here,, The clicking sound you speak of, is it coming from the door latch/catch area of the cabinet,, Can you lean down for me, seta wash program and listen very closly and pin point the origin of the clicking sound,, It will either be near the door handle on the door, or behind the control panel ok, Cheers.

The E34 error code on your Siemens IQ800 washing machine indicates adoor locking problem. Let's troubleshoot this issue step by step:

1. Close the Door Properly:
   • Ensure that the door isfully closeduntil you hear aclick. Sometimes, anexcessive loadof laundry can prevent the door from closing correctly.
   • Check if there's any garment trapped between the door and the frame. Remove it if necessary.
2. Restart the Program:
   • After ensuring the door is properly closed,restart the washing machine program.
   • If the error persists, proceed to the next steps.
3. Check for Door Lock Issues:
   • Verify that thedoor lock mechanismis functioning correctly.
   • Inspect thedoor insurance wiringto ensure there are no loose connections.
   • Look for any blockage or issues with thetriac doorin the control module.

Potential causes and fixes: Battery Terminal Corrosion: Cause: If your Bosch laser receiver has been submerged in water, the battery contacts and sometimes the circuit board may have corroded. Fix: Remove the batteries and clean the battery terminal contacts. Pry open the bottom cover and clean any corrosion on the circuit board. Calibration Issues (for Bosch GLL 2-20): Cause: Dropping the Bosch GLL 2-20 can lead to misalignment and errors. Fix: The best way to address this problem is to calibrate the laser level. You can either contact the Bosch service center or follow the calibration instructions in the manual. General steps for calibrating a laser level with a misaligned pendulum: Remove the screws and outer cover. Locate the pendulum hanging in its stationary position. Remove the glass window of the laser level. Adjust the stationary position of the hanging pendulum using the main adjustment screw. Fine-tune right-left adjustments using other smaller adjustment screws. Reassemble the laser level. Cracked Glass Lens (for Bosch GLL 2-50): Cause: If the horizontal glass lens is cracked, it affects accuracy and safety. Fix: Unfortunately, this problem is often unrepairable. It's advisable to replace the laser level to ensure safe operation1. Remember to lock your laser level when not in use or during transportation to prevent pendulum movement1. If these steps don't resolve the issue, consider reaching out to Bosch for professional assistance or repair

Ideas in the link, but this is a commercial washing machine. https://www.google.com/search?q=super+general+washing+machine+E53+code ..

check door inter lock

try unplug the washer an waiting 5 min it should unlock if , if ti does onlock you made need call a appliance servce tech

It won't be easy - the necklace went through the hole so logically it should come back, unfortunately it is the nature of a necklace to be a random structure unless some tension is applied; the links or whatever are apt to go sideways and jam in the hole. In an extreme case the necklace could be knotted... If it is knotted there is no chance of removal and the solution is either to dismantle the washer or to break the necklace. Positioning the drum so the necklace is under tension under its own weight and with some jiggling and the application of lots of patience and some luck it should come back through the hole.

What's problem machine can't start washing and water incoming non stop?

Free online manual: https://www.manualslib.com/manual/858379/Defy-Automaid-600.html Defy Automaid 600 Owner Manual

How many washing times and what is the minimum time

Question edited for clarity and spelling. Question moved to maker category. Very easy. https://www.google.com/search?q=AEG+Lavamat+509+Washing+Machine.+How+to+replace+pump ..

What is the model number for this washer?

How to reset the samsung wa7584c1 + control panel my washing machine returns the 1E error and its not the pressure switch. when i bypass it works but wants to reset it. How do i operate the control panel to reset. please help 1.To reset the control panel of your Samsung WA7584C1 washing machine, you can follow these steps: 2.Unplug the washing machine from the power outlet. 3.Wait for a few minutes to ensure that any residual power is discharged from the machine. 4.Plug the washing machine back into the power outlet. 5.Press and hold the "Start/Pause" button for approximately 5 seconds. 6.Release the "Start/Pause" button once the control panel lights up or resets. Check if the error code (1E) has been cleared. If the above steps don't work, consult the user manual of your washing machine for specific instructions on how to reset the control panel or troubleshoot the 1E error code. If the issue persists, it may be necessary to contact Samsung customer support for further assistance or to schedule a service appointment.

Troubleshooting chart-

https://machinecompanion.com/maytag-neptune-washer-not-draining/

no schematic listed. https://www.google.com/search?q=Electrolux+EWT604S+schematic Generic Service manual https://tds.electrolux.com/others/599/703/247EN.PDF https://www.google.com/search?q=Electrolux+EWT604S+service+manual ..

Check the Coin Mechanism: Ensure that the coin mechanism is functioning correctly. Sometimes, coins may get stuck or not register properly. Verify that the coin slots are clear and that the mechanism is engaging properly. If there's an issue with the coin mechanism, it could prevent the washer from starting. You might need to clean or repair it. Inspect the Wiring: There should be a harness with two wires that go into the coin mechanism box. Check if these wires are intact and properly connected. If you find any damage or loose connections, consider repairing or replacing the wiring. Bypass the Coin Mechanism: If you suspect that the coin mechanism is causing the problem, you can bypass it temporarily. Cut the wires going into the coin mechanism and insert a push button switch in the line. This will allow you to manually start the washer without relying on the coin mechanism. If you're unsure how to do this, consider contacting a local repair shop for assistance. Check for Other Issues: Inspect other components such as the lid switch, control board, and start button. Any malfunction in these parts could prevent the washer from starting. Make sure the washer is plugged in and that there are no tripped circuit breakers or blown fuses.

When the E4 error appears on your Aftron top-load washer, it usually means there's an issue with how the lid closes or locks. This error prevents the washer from knowing if the lid is shut tightly during use. * Ensure the lid is completely closed and latched. If it's not fully closed, the washer will not start. * Inspect the lid lock for any damage or blockages (e.g., dirt, debris, faulty latch) as these can prevent the lid from locking. * Power off the washing machine and unplug it briefly, reconnect the power and restart the machine, this reset may resolve the error. * Use a multimeter to check if the lid switch has continuity, this test will determine if the switch is functioning properly.

using the flat head screw driver firmly push the tip to the correct direction of the catch and the door would open

Errors TE, EC, TC mean that the temperature sensor that measures the temperature of the water in the unit is not working properly. Some codes - for example, TE - appear only before the start of the wash. These codes are typical of both ordinary washers and those that have a drying function.

If it is only leaking when you use warm water it is likely a leak from the delivery side of the hot water inlet solenoid. The only way to check is to remove the top and look. https://www.google.com/search?q=Kenmore+80+series+washer+92281100+leaks ..