Washing Machines - Page 2 - Recent Questions, Troubleshooting & Support

See page 13 of the user manual.

Drive belt or lid lock safety. https://www.google.com/search?q=Defy+twin+tub%2C+the+dryer+spinner+does+not+spin ..

I had the same problem twice. I removed the top cover and on the metal part in the middel you see a reset button on the right side with 2 connectors. Push the button in the and it will work again.

To remove the drain pump filter on your LG washer model WM2016CW, try gently wiggling and pulling it after removing the cap. If it's stuck, apply lubricant sparingly and tap around the edges. Comparing with your mother-in-law's similar model might offer insights. If all else fails, refer to the manual or contact LG support for assistance.

There appears to be a solution here

Why has my whirlpool washer started asking me about

JustAnswer https://www.justanswer.co.uk > appliance > h42zj-whirl... Jun 24, 2021 - I dont have an error code. I set my washer to wash (press play) it senses then asks 'compartment II 53ml? I have to then press play again ... I have a whirlpool 6th sense zen 12 kg washing machine Jan 7, 2023 Error f24 on my machine, Whirlpool 6 sense I'm not sure how May 1, 2022 How do I remove demo mode from my whirlpool 6th sense 9kg May 13, 2021 My 6th sense Whirlpool dryer has stopped working. 2 red LED Jul 29, 2014 More results from www.justanswer.co.uk A little more here https://www.google.com/search?q=Whirlpool+6th+sense+is+displaying+this+message+Compartment+II+37ml ..

Hi, With the board replacement, did you program this board for this unit? If not, thats the problem you have now. Good Luck I’m happy to help further over the phone at https://www.6ya.com/expert/gere_bf68e6055dd61249

its should be that is the Inverter Drive error. Check to see if the cooling fan is working on the inverter. If not, then when the drive gets hot, it will cut off in the high speed extract. If the fan is working then it's probably an inverter.

Ignore most of these comments. The fix is simple, this machine does this to force you to run a drum clean. Simply hold the lock key button until it unlocks, then run a drum clean cycle.

That sounds like the bearings have collapsed. Time to call a domestic appliance engineer or look for a new machine.

I am sure I answered this yesterday? You posted to washing machines category and this appears to be a gas fueled pool heater. You would be best contacting a service engineer because it is gas powered, although if it does blow up, it is outside or will only blow up the pool house.

Universal H-Series Natural Gas 250000 BTU Low NOx

Hayward Pool Products https://hayward.com > universal-h-series-natural-gas-250... Universal H-Series Natural Gas 250,000 BTU Low NOx. Hayward. SKU: W3H250FDN. Service and diagnostics manuals https://www.google.com/search?q=hayward+250+hd+service+manual ..

Check out the link for Kenmore Parts suppliers. https://www.google.com/search?q=Kenmore+series+200+triple+action+agitator+parts ..

advise you take the top off so you can see where the bolts locate

You are using the wrong type of detergent. Use liquid instead of granulated powders. They don't dissolve in low temperatures. https://www.manua.ls/lg/wf-8071ttp/manual?p=8 ..

Videos in the link https://www.google.com/search?q=Samsung+WA80G5+washing+machine+pulsator+is+not+working ..

If your IG Ignis 105 LA washing machine does not show any lights after a low voltage run and power surge, check the power supply, main control board, and internal fuses for damage. Consider contacting IG Ignis customer support for remote troubleshooting guidance or arranging for a technician to inspect and repair the appliance.Hi Tracey and welcome to JA, sorry for the delayed response, flat out all day here,, The clicking sound you speak of, is it coming from the door latch/catch area of the cabinet,, Can you lean down for me, seta wash program and listen very closly and pin point the origin of the clicking sound,, It will either be near the door handle on the door, or behind the control panel ok, Cheers.

The E34 error code on your Siemens IQ800 washing machine indicates adoor locking problem. Let's troubleshoot this issue step by step:

1. Close the Door Properly:
   • Ensure that the door isfully closeduntil you hear aclick. Sometimes, anexcessive loadof laundry can prevent the door from closing correctly.
   • Check if there's any garment trapped between the door and the frame. Remove it if necessary.
2. Restart the Program:
   • After ensuring the door is properly closed,restart the washing machine program.
   • If the error persists, proceed to the next steps.
3. Check for Door Lock Issues:
   • Verify that thedoor lock mechanismis functioning correctly.
   • Inspect thedoor insurance wiringto ensure there are no loose connections.
   • Look for any blockage or issues with thetriac doorin the control module.

Potential causes and fixes: Battery Terminal Corrosion: Cause: If your Bosch laser receiver has been submerged in water, the battery contacts and sometimes the circuit board may have corroded. Fix: Remove the batteries and clean the battery terminal contacts. Pry open the bottom cover and clean any corrosion on the circuit board. Calibration Issues (for Bosch GLL 2-20): Cause: Dropping the Bosch GLL 2-20 can lead to misalignment and errors. Fix: The best way to address this problem is to calibrate the laser level. You can either contact the Bosch service center or follow the calibration instructions in the manual. General steps for calibrating a laser level with a misaligned pendulum: Remove the screws and outer cover. Locate the pendulum hanging in its stationary position. Remove the glass window of the laser level. Adjust the stationary position of the hanging pendulum using the main adjustment screw. Fine-tune right-left adjustments using other smaller adjustment screws. Reassemble the laser level. Cracked Glass Lens (for Bosch GLL 2-50): Cause: If the horizontal glass lens is cracked, it affects accuracy and safety. Fix: Unfortunately, this problem is often unrepairable. It's advisable to replace the laser level to ensure safe operation1. Remember to lock your laser level when not in use or during transportation to prevent pendulum movement1. If these steps don't resolve the issue, consider reaching out to Bosch for professional assistance or repair

Ideas in the link, but this is a commercial washing machine. https://www.google.com/search?q=super+general+washing+machine+E53+code ..

check door inter lock

try unplug the washer an waiting 5 min it should unlock if , if ti does onlock you made need call a appliance servce tech