Sewing Machines - Page 4 - Recent Questions, Troubleshooting & Support
Tl2200 sit down threads locking under work and have to be cut to move quilt
- seems as though you're encountering trouble while sewing little plans like stones, where the development becomes more diligently and afterward stalls out. This could be because of different factors, for example, needle issues, string strain, or machine support. Checking these angles could assist with further developing the sewing system.
Manual for Toyota RA41 RS2000 series
Manualslib.com has manuals for all sorts of things. I did a quick search and found this: https://www.manualslib.com/manual/998886/Toyota-Rs2000.html
My Pfaff quilt Expression 4.0 feed dogs will not go down. The switch will not lower them.
I assume the switch you are talking about is the one on the front bottom of the machine. this switch should not slide back and forth easily, if it does than the linkage has been disconnected or broken. To check this you need to open the bottom of the machine and see what happens when you move the switch. To open the bottom you will need a torx screwdriver. First remove 4 long screws that go through bottom and into back, than remove two shorter screws that go through bottom into front cover, next remove 3 short bolts that hold the bottom to frame. If you can't see anything broken or loose after opening the bottom, you might need to remove the covers.
Huskylock hand wheel wont turn or needles wont go down
If the handwheel on your Huskylock machine won't turn and the needles won't go down, there may be several issues. Check for thread jams, tangled threads, or broken needles in the bobbin area. Ensure that the machine is properly threaded, the presser foot is down, and the stitch length is not set to zero. If the problem persists, it could be a mechanical issue or a need for lubrication. Consult the machine's manual for troubleshooting tips or contact the manufacturer's customer support. If you're not comfortable addressing the problem, seek assistance from a qualified technician or service center. click
I am getting error message Presser foot too high but foot is all the way down
If you're encountering a "Presser Foot Too High" error despite the foot being down, check for potential issues. Ensure the machine is threaded correctly, the needle is not bent, and the presser foot is securely attached. Verify if there's any fabric or thread caught in the mechanism. Additionally, consult the machine's manual for troubleshooting steps or contact the manufacturer's customer support. If the problem persists, it might indicate a mechanical issue that requires professional inspection. In some cases, recalibrating the machine or updating its software may resolve the error. Always follow safety guidelines and turn off the machine before attempting any adjustments. click
White Mighty Mender W100 Mini Sewing Machine. I am just trying to figure out how to actually use my Mighty Mender mini sewing machine, the W100.
To use the White Mighty Mender W100 Mini Sewing Machine, follow these steps:
1. Place the machine on a flat, stable surface.
2. Plug in the machine and turn it on.
3. Thread the machine by following the threading guide provided in the manual. Make sure to use the correct thread and needle for your project.
4. Place your fabric under the presser foot and lower the foot to hold the fabric in place.
5. Use the handwheel to lower the needle into the fabric at the starting point.
6. Press the foot pedal or use the start button to begin sewing.
7. Guide the fabric through the machine while sewing, keeping a steady pace.
8. When you reach the end of your seam, use the reverse lever (if available) to backstitch and secure the stitches.
9. Lift the presser foot and trim the thread.
For more detailed instructions, refer to the user manual that came with your Mighty Mender W100 Mini Sewing Machine. If you don't have the manual, you may be able to find one online by searching for "White Mighty Mender W100 manual" or contacting the manufacturer directly.
Replace floppy drive with USB on a Designer 1
Check with a Viking dealer whether Viking offers a conversion kit. My guess is that rather than offer such a kit, Viking would rather sell replacement floppy drives or a newer model of machine.
2/3/2024 4:01:38 PM •
Husqvarna...
•
Answered
on Feb 03, 2024
THREAD COLLECTS UNDER MY YAMATA FY 760
try changing the needlerethread the machine top & bobbinclean under the needle plate & in the bobbin area for loose threads or lintcheck to make sure the bobbin & bobbin case is not damaged
Am looking for the manual for empisal super automatic passeter model 220~250 50hz 70w no 114886
Hello, Linda -
I found the Empisal home page and looked through the sewing machine manuals they offer for download. None of them were for your Pacesetter model.
If you have not yet done so, I suggest you contact the company directly (via a telephone call or email message) and ask if a manual for your model is in the corporate archives, and if it is, ask if the company can scan it as a PDF document for you. If that is possible, the PDF document can be attached to an email and sent to you.
Note: For any PDF document, you will need Adobe Reader software (free).
This is the link to the Empisal Contact Us page:
http://www.empisal.co.za/contact-us/
The Physical Address section is where you will find the email address and telephone number for the Johannesburg, South Africa based company.
Best wishes.
Not finding what you are looking for?