Saws - Answered Questions & Fixed Issues

If the fuel in it is 2 or more months old dump it out and put in fresh fuel and try statring. Also try try a squirt of starting fluid into the carb. If it fires on it you may need to do this a few times to pull the old fuel in the lines through till the fresh fuel can get to the carb.

It is an STS 325 R, but even with the model number in the right order, there is no repair manual for it, just user manual and parts list. Ask Fein direct. https://www.google.com/search?q=fein+air+saw+STS+325+R+repair+manual ..

The manual for the saw is included below, To free the height it may be best to remove the saw carriage from the arm to reduce the weight. Use WD40 or equivalent to cut the rust and a suitable grease to maintain the freedom. There is a worm screw that is below the cylinder that may need lubricating. The manual shows the assembly. I routinely apply 90 weight gear oil around the large tube where it goes into the housing, http://vintagemachinery.org/pubs/252/1213.pdf Hope this helps? http://vintagemachinery.org/pubs/detail.aspx?id=1213

closes I could find.copy and paste.https://www.carbatec.com.au/documents/manuals/Carbatec/Bandsaws/SW-1401-manual.pdf

Question edited for clarity, 'make model (what it is)', in full. No manual, just parts. Try black and Decker direct. https://www.google.com/search?q=black+and+decker+9443+bandsaw+manual https://support.blackanddecker.com/hc/en-us/p/all_locations ..

@Brian AndersonIt is better to write a new question rather than tagging an unsolved question from 10 years ago. It is now stuck on the Homepage as 'Pinned' and still showing Unsolved! :>Dhttps://www.google.com/search?q=+Dewalt+DW936+remove+the+guard+assembly..

It should be an issue of calibration, but no one else has experienced this issue. contact SCM Support direct. https://www.google.com/search?q=SCM+Nova+SI+400EP+Sliding+Table+Saw+calibration ..

What is a timing belt in this case? I have two radial arm saws (a Sears and a Monkey Ward) and neither one had what I would call a time belt. My saws were direct drive (through they were gear reduction direct drive).

Is this a tooth belt of some type? If so, I doubt that it is anything really special like custom made for a run of saws. Someone must make such a thing.

Again, I dont know what we are looking at ... having said that ... were I looking for a special belt, Id first visit a good auto parts store ... not a big box nor fast food type but a genuine old fashioned auto parts place. The one with some greas on the counter. Ask the counterman or woman if they can help. Take your sample with you.

Next, I think I'd visit Gates Power (they make all kinds of belts) I could get you a link ... but hey ... you found this place didnt you? you can find gates belts!

As a last ditch effort, you could put a want add up at e-bay.

I hope some of these ideas help you find the part you need.

Please tell me more acout this belt for for my general knowledge. Thanks

How to get manual of DeWalt bs 1310??

Try a shot of WD40 and leave it to sit for 10 minutes, then spray again. https://www.google.com/search?q=Scorpion+Saw ..

https://www.manualslib.com/manual/1823573/Twin-Cut-Power-SawPlus.html?page=17#manual

Question edited for clarity, 'make model (what is is)'. Question moved from Washing Machines category. E1 Error, but not E.H1. https://www.google.com/search?q=Altendorf+WA80+error+code+EH1 Manual Errors and Troubleshooting. https://www.manualslib.com/manual/1583371/Altendorf-Wa-80.html?page=45 ..

..

How to use model number 84-6460

It may be this one by Sears under a different name. It shows bench adjustment parts via schematic. https://www.searspartsdirect.com/model/4upjq1jecw-003073/pro-tech-4002-table-saw-parts _A_ manual, not necessarily _THE_ manual https://c.searspartsdirect.com/mmh/lis_pdf/OWNM/L0604856.pdf https://www.google.com/search?q=Benchtop+10in+table+saw+05-30-13+%284002%29+manual ..

Question edited for clarity. Question moved to Kobalt Saws. Didn't I answer this a few days ago? Here are the parts suppliers for it. https://www.google.com/search?q=kobalt+kws+s72-06+replacement+parts ..

if keeps tripping breaker use multi to check plug wire or motor short

Parts suppliers https://www.google.com/search?q=felker+wet+saw+parts ..

Question edited for clarity. Question moved from Computers. Nothing on them apart from people selling them. https://www.google.com/search?q=shopcraft+T6780-87 No manual, but any table saw manual with probably suffice. https://www.google.com/search?q=shopcraft+T6780+manual ..

If you take it to an electrician, the issue may well be the suppressor capacitor, across the switch contact, will be short circuit. Get it replaced with a suitable Class Y components and it will be working again. OR thee switch is faulty. Replaceable by a commonly available spare part. Being 15 years old, there is little hope of a spare parts manual but it is a very basic design and should be easily repaired by a competent engineer.