Food Mixers - Page 3 - Recent Questions, Troubleshooting & Support

Try fleabay.

Parts suppliers, and a link to the maker. For some reason the parts list doesn't show the Stop Button, just mechanical parts? https://eurodib.com/wp-content/uploads/2021/02/%EF%BC%AD-Series-Food-Mixers-ENG.pdf https://www.google.com/search?q=Eurodib+M20A+mixer+parts ..

Could be anything, but could be the switch, the electronics board, motor windings, the carbon brushes or worn insulation somewhere. Odd that the plug fuse didn't blow. It needs electrical diagnosis to find out what went wrong.

Service & Support Owners Center

KitchenAid https://www.kitchenaid.ca > en_ca > service-and-support Make an appointment from our preferred list of service providers for service on your major appliances. ... Pro Line® Series Stand Mixers Stand Mixer Attachments ... ..

Question edited for clarity. Question moved from Russell Hobbs Washing Machines. an appliance repairer would look at it for you unless you wish to try yourself. Mine has 4 screws underneath to get access to the motor. The issue in normally that the carbon brushes on the motor either wear out or stick. If the electronics for the timer have failed, it is unlikely that you can get parts, but worth a try. https://www.google.com/search?q=russell+hobbs+rhmx1+hand+mixer+repair ..

My experience with electrics has mostly been coffee grinders, hand held food blenders and vacuum cleaners but these are the checks I do. Sadly you'll have to open her up again to do these. Personally I wouldn't use compressed air. Some compressor pressures can be a bit too powerful. I would suggest a vacuum. Stick the foot end of a pair of tights (pantyhose) over the nozzle that way you get suction but you don't lose nuts and screws up into the vacuum. Opening her up again might reveal a loose wire you missed rebuilding it. That was my issue with a vacuum cleaner I rebuilt. -Turn the motor by hand using the shaft the blade bolts to. Your feeling for it smoothly and quietly turning. If it's gritty, noisy or your getting tight spots there's dirt or something inside or a bearing is worn out. -Test for voltage at every point where a wire ends and connects to something else like switches, circuit boards and the motor itself. -Disconnect the wires to the motor and test for Continuity. Set your Multi meter to Ohms (the little horse shoe symbol) and touch the test probes, one each motor terminal. You should get a very low number somewhere near zero. Most multimeters will beep when you have continuity. If you get an 'L' or 'OL' there's a short or a broken wire. -I would then do the same test across all the switches on the machine, wires off and test the switch. Just because they move doesn't mean they're working. These steps usually work for me so give them a try, the multimeter won't hurt the machine.

Question edited for clarity. There isn't much in the way of parts advertised, but the company is still in business https://www.google.com/search?q=Ankarsrum+Stand+Mixer+parts You may have more luck with the Electrolux version https://www.google.com/search?q=Electrolux+Kitchen+Assistant+parts ..

First try adjusting it. The head may be set so low, the head can't latch. Does it latch with no whisk attachment? The video shows how to adjust it with the whisk in place using a dime.. If that isn't the reason, spares are available and dealer service is available. https://www.google.com/search?q=cuisinart+5.5+stand+mixer+parts ..

Videos that may help, but it is probably a repair centre job. https://www.google.com/search?q=Cooks+stand+mixer+lift+lever+repair ..

The handle appears to be bare on this industrial catering mixer. https://www.google.com/search?q=globe+sp20+mixer+manual ..

The safety Lock on the bowl hasn't released. You will see it in a tube where the lid lock is. When the lid it locked into place, it pushes a rod down into a hole in the base to operate the safety switch. You may be able to pull it up with needle nose pliers. https://www.google.com/search?q=how+a+food+processor+lid+safety+lock+works That is a funny looking machine, so none of what I wrote may apply! https://www.google.com/search?q=bosch+universal+kitchen+machine

Check the power supply: Ensure that the food processor is properly plugged into a functioning power outlet. Sometimes, a loose connection or a tripped circuit breaker can cause power issues.

Safety interlock system: The Kenwood Multipro 910 food processor usually has a safety interlock system that ensures all parts are properly assembled before it can start. Check if all the components, such as the bowl, lid, and blade, are correctly locked into place. If any of the parts are not properly assembled, the food processor may not work.

Motor overload protection: If you have been using the food processor for an extended period or with heavy ingredients, the motor may have overheated and triggered the overload protection mechanism. In this case, you will need to allow the motor to cool down for some time before it can restart.

Fuse or circuit breaker: Some food processors have a built-in fuse or circuit breaker that protects the motor from electrical surges. Check if your food processor has a fuse and ensure that it is intact. If it has a circuit breaker, reset it if necessary.

Mechanical issues: If none of the above steps resolve the problem, there might be a mechanical issue with the food processor. It could be a faulty motor, broken wiring, or a malfunctioning switch. In such cases, it is advisable to contact the Kenwood customer support or take the appliance to an authorized service center for repair.

1. Use the plug to rotate and pull out the plate 2. remove the two screws circled in yellow 3. Very carefully unclip the top of the handle, the clips are easy to break 4. remove the spring 5. unclip the black plunger, by squeezing the tabs underneath 6. disconnect the switch board 7. remove the screw circled in yellow 8. the whole assembly can now be removed from the housing

It is not a make I have heard of before, which is odd, because I spent 50 years in catering and hospitality. Parts are available according to this. Getting to the snap ring would be the issue. You may be able to pull the old one out with a right angle pick and push the new one in. https://www.google.com/search?q=blakeslee+a717+parts ..

Well done Leonard. Easy fix.

If your stand cake mixer is not working and you suspect that water may have entered the device, it's possible that a fuse or other electrical component may have been affected. Here are a few steps you can take to troubleshoot and potentially fix the issue:

1. Unplug the mixer: As a safety precaution, unplug the mixer from the power source before attempting any troubleshooting or repairs.
2. Let it dry: If water has indeed entered the mixer, allow it to dry thoroughly before attempting to use it again. Place the mixer in a warm and dry environment for a few days to ensure all moisture has evaporated. Do not attempt to use the mixer while it is still wet, as it can be dangerous.
3. Check for visible damage: Once the mixer is dry, carefully inspect the external components for any visible signs of damage, such as burnt marks or loose wires. Pay close attention to the power cord and the area where it connects to the mixer.
4. Check the fuse: Some mixers may have a fuse that protects against electrical issues. Refer to the user manual or consult the manufacturer's website to determine if your mixer has a fuse and its location. If the fuse is accessible, check to see if it has blown and replace it if necessary. Use the recommended fuse rating specified by the manufacturer.
5. Seek professional help: If the above steps do not resolve the issue, it's advisable to contact the manufacturer's customer support or consult a qualified appliance technician. They will have the expertise and knowledge to diagnose and repair any internal electrical problems safely.

Water damage can be a simple fix or very costly. Contact a service department to arrange an engineers visit and estimate.

You need to contact an electronic component supplier, there are many on line, they can answer that question for you.