Hi! If your Defiant Motion Outdoor Light flashed red and stopped working, there could be a few potential causes for this issue. Here are some steps you can take to troubleshoot the problem:
Check the power source: Ensure that the light is receiving power by verifying that the circuit breaker or fuse connected to the light is not tripped or blown. If it is, reset the breaker or replace the fuse and see if the light functions properly.
Inspect the bulb: The red flashing light could be an indication of a bulb issue. Remove the bulb from the fixture and inspect it for any signs of damage or a burned-out filament. Replace the bulb with a new one if necessary and see if that resolves the problem.
Check the motion sensor settings: Some motion lights have adjustable sensitivity settings. Make sure the sensitivity setting is properly adjusted to detect motion as desired. Consult the user manual or manufacturer's instructions for your specific model to learn how to adjust the motion sensor settings.
Reset the light: Sometimes, a simple reset can fix the issue. Turn off the power to the light at the circuit breaker or by disconnecting it from the power source. Leave it off for a few minutes, and then restore the power. This can help reset the light and clear any temporary malfunctions.
Verify the wiring: Inspect the wiring connections for any loose or damaged wires. Ensure that the wiring is properly connected and secure. If you find any issues, consult a qualified electrician to address the wiring problem.
If none of these steps resolve the issue, it's possible that there may be a defect with the light itself. In that case, you may need to contact the manufacturer or return the light for repair or replacement, especially if it is still under warranty.
You are pretty stuck with that scenario. With an electronic lock you can use a rare earth magnet to pull the locking bolt but with a manual dial safe, you can't do that. I can remember my business safe combination from 1987 to 2005. You can also write it down.
Use a concrete saw or angle grinder and cut the back off it.
..
If your KKmoon NVR turns on but won't show camera feed on your screen, here are a few troubleshooting steps you can try:
Check the cables: Make sure all cables are securely connected and that the camera is powered on.
Check the NVR settings: Ensure that the NVR is set to display the correct camera channel. Go to the NVR's menu and look for a setting related to camera input or channel selection.
Check the resolution: Make sure the resolution of your monitor is set correctly. If the monitor's resolution is too low, it may not be able to display the camera feed.
Update the NVR's firmware: Outdated firmware can cause problems with the NVR's functionality. Check the KKmoon website for any available firmware updates.
Restart the NVR and monitor: Sometimes a simple restart of the NVR and monitor can resolve the issue. Unplug both devices, wait for a few seconds, and then plug them back in.
If none of these steps resolve the issue, you may need to consult the NVR's user manual or contact the manufacturer for further assistance.
Best Buy says 'No'!
This camera will not work with any other system. The camera and monitor both have antennas that work together, and the cameras are already "paired" to work with the Defender monitor.
Oct 29, 2018
I posted this last night for another safe.
You can open it faster with a rare earth puck magnet than you can inputting the code. The word 'Safe' is a misnomer.
Posted on May 31, 2023
I am a Safe Specialist i have been reading some of your problems and this should help there is no code if you have lost yours only the default code for the model 1610 the default code is: 77,22,09,11,64 try that if you havent changed it and with this problem with people not getting the handle open with the green light happening i suspect this is a issue with the lock mechanism i have had many of the same problems with people bringing them in when you get you safe open it and where the lock is put some lubricate on the lock regulary as the lock sticks and wont open if you havent done this then you cannot get it open see you local safe specialist and tell them what i have said and they may or may not be able to get your safe open i hope this has helped Rob Safe Specialist World.
Power off the DVR: Make sure the DVR is powered off by disconnecting it from the power source.
Locate the reset button: On the back or bottom of the DVR, you should find a small reset button. It is often recessed and may require a pointed object like a paperclip or pin to press.
Press and hold the reset button: Using a suitable tool, press and hold the reset button for about 15 to 30 seconds. This will reset the DVR to its default settings, including the password.
Power on the DVR: After releasing the reset button, reconnect the DVR to the power source and power it on. The DVR will go through a startup process.
Access the DVR: Once the DVR has finished booting up, you should be able to access it using the default login credentials.
Username: The default username is usually "admin" or "admin1234". If these do not work, consult the DVR's user manual or documentation for the correct default username.
Password: The default password is typically either blank (no password) or set to "4321". If none of these options work, refer to the DVR's documentation or contact Samsung's technical support for assistance.
The specific capabilities and settings of the PnP brand 30W motion sensor LED floodlight may vary depending on the model and design. However, in general, motion sensor LED floodlights are typically designed to operate based on detected motion and have a preset duration for illumination after motion is detected.
If you would like the PnP 30W motion sensor LED floodlight to remain on permanently, overriding the motion sensor function, you can try the following steps:
1. Locate the settings: Check if the floodlight has any accessible settings or switches that allow you to adjust its operation. This could be located on the fixture itself or on a separate control module if provided.
2. Disable or bypass the motion sensor: Look for an option to disable or bypass the motion sensor function. This might involve flipping a switch, pressing a button sequence, or adjusting a specific setting. Consult the product manual or contact the manufacturer's customer support for guidance on how to accomplish this for your specific model.
3. Connect the floodlight to a separate power source: If disabling the motion sensor function is not possible or practical, you can consider connecting the floodlight to a separate power source that provides constant power. This could involve bypassing the original wiring or using a separate switch or power outlet that remains on continuously.
It's important to note that overriding the motion sensor function may affect the energy efficiency and intended purpose of the floodlight. Motion sensor lights are typically designed to conserve energy by only activating when motion is detected, providing illumination when needed. Keeping the light on permanently may result in increased energy consumption and reduced bulb lifespan.
Always refer to the product manual or consult the manufacturer's instructions for the specific model of the PnP 30W motion sensor LED floodlight to ensure you understand its features and limitations.
You need someone to connect an Elsafe Servicing Unit to supply external battery power via the connection cable to power up the device so that you can unlock the safe. The servicing unit attaches to a 9 volt battery to rescue failed safes due to battery problem. Once the safe is open, you can replace the safe's dead batteries.
Option 2: Get someone to drill the safe open.
Question edited for clarity.
Although this guy makes it look hard work, they will usually bounce open quicker that this. You can also bang the top with a rubber mallet, or use a rare earth puck magnet to pull the actuator bolt.
Question edited for clarity.
Question moved from Heating and Cooling.
You can open it with the backup key and replace the depleted batteries. Then reset a new combination.
All this type of safe can be opened with a large rare earth magnet faster than using the combination!