Drywall - Answered Questions & Fixed Issues

If you screw into plasterboard, they will. Use specific plugs to allow the screw to grip without falling out or screw into wood that supports the plasterboard. Drywall screws are used to hold plasterboard/drymall sheeting, in place, not for fixing to plasterboard as the board will fall apart.

https://youtu.be/EhmQTkfYATs This is the link. Watch this video.

Screws if you have not already used. Then as follows:
Joint compound
Joint tape
Then texture if desired
Primer
Paint

You need to investigate the cause. Where there is mould, there is damp... If it was through the previous occupiers using things like tumble dryers, irons etc in enclosed spaces without sufficient ventilation then that's one thing. Damp on walls always needs investigating though to ensure the house is structurally sound. Have you had an extended survey done?

I don't think a Dremel has enough power to do what your after. However there is a larger rotary tool made by several different company's mine is made Dewalt works great fairly inexpensive and will do what you need.

The stud finders are not expensive but you can sometimes use a magnet to find the nails. Also you might try shining a flashlight across the wall. The putty put over the nails will sometimes show up. Last resort is to tap on the wall and try and hear the areas that have support under them.

5/8 of an inch is recommended. You may be able to get away with 1/2 inch if you don't really care, but i would check with the building inspector first

No.

What application are you wanting to use it for?

Not if it isn’t going to show.

If you are asking how to install drywall the best way is with screws.

You can either measure up from the floor or the piece of drywall you just hang and then measure over from the wall or the piece of drywall you just hang or you can put the drywall in place and I ball behind it and Mark with a pencil and then cut it out with a dremel tool and you should be good from there. You might want to use a keyhole saw or a roto zip and a Rotozip is the best way to do it but it takes a little practice in order to control it

Thermal couple is a sencing wire that sends a signal to your gas valve when the tip Spence’s heat from a pilot light! Can be purchased at any hardware or big box store,eg. Home Depot/ Lowe’s And any plumbing supply store. Average price is $$6-8.

hi there. Sink A Self-Drilling (Threaded) Anchor

1. Mark your hanging point with a pencil.
2. Tap the pointed tip of the anchor into the wall with a hammer.
3. Once the tip is in the drywall, with a screwdriver, screw the anchor in until it's flush to the wall.

Fix-It Friday: Anchors Aweigh! How To Put Anchors Into Walls

womenyoushouldknow.net/fix-it-friday-anchors-aweigh-how-to-put-anchors-into-walls/ How to Install Drywall Anchors to Hang Heavy Stuff on Your Walls How do hang an object using drywall anchors Google Search

Sometimes you can wrap a piece of thin plastic or paper around the stem and shove it back in and will hold it in place,- other wise there is a spring steel clip that probable wore out and would need to be replace but it wont be fun

Yes-just let dry after-then on prep of wall after you may have to skim wall with a thin coat of drywall compound and sand smooth

it usually has that on the label-depends on which gun you have also

2 cups

Wow all those answers are ok but easy way is to wad up a piece of paper larger than the hole-force piece of that paper into hole slowly not to force into cavity behind just slightly flush then stop-take a putty knife and float with drywall compound you can get a small container of that compound at walmart even-then repeat and sand between coats until you are flush and smooth-if there is a texture then on last coat take a roller and run it thru the wet compound

Get you some heavy duty liquid nail or similar adhesive, put it in strings/loops, wait a bit, put rock on, hold a bit done