Drills - Answered Questions & Fixed Issues
When ever I put on my battery on my dewalt charger the indicator light blinks faster than normal while charging
Possible reasons for this behavior:
Blinks Long (Red Light): If your battery is too hot, the charger will blink the red light rapidly and for an extended duration. To prevent this, ensure that your battery is not exposed to direct sunlight or excessive heat. Give it some rest to cool down.
Blinks Short: If the battery is too cold, it will blink short and fast. This could be due to prolonged exposure to cold temperatures or the battery being idle for an extended period. Allow the battery to charge for a while or bring it to room temperature to resolve this issue.
Blinks Very Fast (Doesn't Go Away): If the light is blinking very fast and persists, it indicates that your battery has gone bad and needs replacement.
4/16/2024 5:36:07 AM •
Dewalt Drills
•
Answered
3 days ago
•
14 views
How to remove oven door Maytag mgr5775qds
To remove the oven door on a Maytag MGR5775QDS range, you can follow these general steps:
- Open the oven door completely to access the hinges.
- Locate the hinge locks on both sides of the door. These are usually small levers or clips.
- Use a flathead screwdriver or your fingers to flip the hinge locks toward the oven cavity, releasing them from their locked position.
- With the hinge locks released, close the oven door halfway.
- Lift the oven door up and off the hinges by pulling it toward you and lifting it away from the oven.
- Place the oven door on a flat surface, such as a table or countertop, to work on it or store it.
Remember to exercise caution when handling the oven door, as it may be heavy and awkward to maneuver. If you're unsure or uncomfortable with removing the oven door yourself, it's always a good idea to consult the appliance's manual or contact a professional for assistance.
2/17/2024 5:19:51 PM •
Drills
•
Answered
on Feb 17, 2024
•
29 views
I have a DeWalt D2570 - GB. Stopped working. On disassembly I found a bare wire from the capacitor. Where should it go?
A photo would greatly help with your issue, are both wires still attached to the capacitor?? in not, the capacitor must be replaced with one of the same value,
if the capacitor is ok, look for a wire with solder on the end but nothing else attached to it, or a solder point on a card with a hole in it or a solder joint that has broken free from the card,,, if you can solder well, and have the equipment,. it is good at this point because You'll need to re-solder them back together,,
again a photo will help me greatly in telling you exactly how to fix
2/15/2024 1:40:25 PM •
Dewalt Drills
•
Answered
on Feb 15, 2024
•
77 views
I need a new baterie how a buy the barerie
if you live in usa ACE HARDWARE sell the battery. if you dont live in usa the go onto the internet GOOGLE and type in MANSFEILD DRILLS, there is 10 pages of information ,and they will yell you where to in whatever country you live in --------- that should help you
2/13/2024 1:45:58 AM •
Mansfield...
•
Answered
on Feb 13, 2024
•
486 views
How to remove the chuck for Black & Decker 4.5 Amp Drill.
Insert the short end of a 1/4" or larger hex Allen wrench into the chuck and tighten. Facing the tool strike the long end of the hex wrench sharply counter clockwise as it is a standard right hand thread. This will loosen the chuck so that it may be unscrewed by hand.
Oct 12, 2022
..
1/23/2024 6:34:51 AM •
Drills
•
Answered
on Jan 23, 2024
•
29 views
Hilti switch acted 7358 ?
How is it acting? All posts need some form of explanation of the issue rather than a vague statement.
Start with 'make model (what it is)' as first three words. Then what is wrong and what you have tried. Proof read it, make sure it is properly capitalized and punctuated and then press Post. Refresh the page to see it online.
..
12/15/2023 6:27:15 PM •
Hilti Drills
•
Answered
on Dec 15, 2023
•
24 views
Not finding what you are looking for?