Dishwashers - Answered Questions & Fixed Issues

Question edited to move it from Computers to Dishwashers. Is there by any chance a floor tile 4" out from the dishwasher front? If so, try lifting the front with a crowbar or long screwdriver. Did you disconnect, inlet hose, drain and power? They may have been installed tight, or clipped. ..

Blockage in the line from the diishwasher to the ABS drain pipe .

Question edited for clarity. Error codes should be on the rear label according to the Technical Manual https://www.partstown.ca/modelManual/HOB-AM15T_spm.pdf There is no E1 error code for that machine and is is suggested that the display may be faulty. https://www.google.com/search?q=hobart+am15+e1+error+code The only reference to E1 is here, for the AM-16 and an electrical 'type'. https://www.hobart.ca/wp-content/uploads/pdfs/warewash/AM16-BAS-Base-Electric-CF48568.pdf For LXi machines Drain and fill error messages are displayed as E0, E1, E2, E3, E4, E5, E6 or E7. In all cases, the dishwasher will terminate current cycle operations, turn off all heat sources and display the message until the OFF button is pressed. (A power drain will not occur when turned off.) (See Troubleshooting.) If problem persists, contact your local Hobart Service Office Phone Hobart Support. there are no Hobart Techs here, just me as caterer, career long Hobart user and Expert finder of information. Or try JustAnswer dot com. ..

It depends upon the material you are trying to repair but Araldite or any good quality two part epoxy will suffice to fill the hole. Ensure the area is dry and clean then build up the repair . Larger holes will require multi additions of epoxy.

Put in olle dishwasher parts and where you live . This should come up with shops that do the spares

Question edited for clarity. Question moved from Cars and Trucks category. This appears to be a Dutch Maker, we are in North America. There is some help here, but I don't see the wiring for that model, although there is a parts manual. The link may work better for where you live. https://www.google.com/search?q=elettrobar+e35h+wiring+diagram+pdf ..

Question edited for clarity. Manual https://www.manualslib.com/products/Kenmore-665-Prefix-257208.html More here https://www.google.com/search?q=kenmore+Dishwasher+model+665+1678582+manual ..

These error messages both point to a sensor problem. Error 12.1 This error is related to the boiler temperature sensor. Consider the following: Look for a short circuit in the sensor. Inspect the cables and plugs for any issues. Ensure the sensor is correctly connected.If needed, replace the boiler temperature sensor. Error 22.2: This error pertains to the tank temperature sensor. Possible causes include: Short circuit in the sensor. Cable failure or plug failure. Sensor not properly connected. You may need to check the sensor wiring, connections, and replace the temperature sensor if necessary.

It has run out of salt or the sensor is blocked.

It is probably in timer mode. Consult your user manual.

Unlikely to be the wiring. It can only be the motor, the door switch, the flood sensor, the motherboard or the control panel. Unfortunately no Service Manual for that model. https://www.google.com/search?q=whirlpool+dishwasher+gu2451+xtst2+service+manual https://www.google.com/search?q=whirlpool+dishwasher+gu2451+wiring+diagram ..

It has a leak into the drain pan. It is flood protection.

Haier Dishwasher Error Codes Explained

Exclusive Repairs https://exclusiverepairs.co.uk > Blog Dec 8, 2021 - Haier dishwasher E6 error code indicates that the flood protection device has been activated and the water supply will need to be turned off, . ..

Could be an over fill issue causing water to leak into the base. What you need to do is pull the dishwasher out and lay it on its back and this will allow the water to drain out from the base.

Don't Worry. Google is your friend... Google Search your Make & Model number & Add service manual, service manual.pdf download, ,service manual parts list, Schematic , or just parts List. Google will bring up a vast amount of information & most of it not what you are looking for BUT If you adhere your search specifically for the information you require, It Should bring up what you are looking for as well as Outlets & phone number you can call to check for such parts. Don't be afraid to Be a little cheeky over the telephone & Ask (if they can't help) if they can recommend an outlet that could help.. OH and have they got that particular number too ;)

Try a power disconnect from the mains for 5 minutes and then plug it back in. It that doesn't fix it, the problem will be the main control board. Many parts are obsolete. https://www.google.com/search?q=GLD4908T10BB ..

This is exclusively a South African model, and you are right, there is no timer available. How old is the machine? Spares are normally carried for 10 years. Big cities normally have an appliance spares outlet where you can an existing part and say "have you got something that looks like this."? You really just need a timer with the same number of contacts on the back. Something else you could do is put a Watch List on eBay. https://www.google.com/search?q=Kelvinator+kd12ww+timer+replacement ..

The date of manufacture is determined by the SERIAL NUMBER on the appliance. This dishwasher was manufactured by Whirlpool. The following link explains how to determine when it was manufactured:

http://www.fixya.com/support/r3576437-determining_the_age_of_your_whirlpool_ap

The serial number is usually located somewhere around the door opening. The first two numbers in the serial number identify the WEEK it was manufactured (52 weeks in a year). The second DIGIT in the serial represents the YEAR it was manufactured.

If you have difficulty determining the manufacture date, please post back with your serial number and I will assist you. I hope you find this information helpful.

Question edited for clarity, 'make model (what it is)'. https://www.google.com/search?q=meiko+upster+u+500+error+9 ..

Make and model of dishwasher may help yu get an answer