Car Audio & Video - Page 2 - Recent Questions, Troubleshooting & Support

No, you can't do upgrades because the stereo is monitored and run by the Body Control Module. Things like warning chimes and the blinker clicker is played through your audio system. The factory Bose stereo should be more that adequate. You can try it, but things generally don't work out like you expect. ..

First thing to do is check to make sure that the batteries are properly charged.

Second, make sure that you have a clear line-of-site to the IR transmitter. Infrared (IR) works the same way that your TVs remote control works - if the signal is blocked, then you will not hear any sound.

Third, make sure that you are in the rear seat of the vehicle when listening to the sound. The IR transmitter only transmits to the rear seat, so you will not hear any sound if you are sitting in the front seats. This is a common problem that i see.

Lastly, make sure that the heapdhones you purchased are compatible with your 2006 2007 2008 2009 or 2010 Toyota Sienna. Remember that some older models require RF headphones, not IR headphones. I checked http://www.audiovideo2go.com for compatibility before I purchased my headphones. They have a useful listing of all the headphones and models of vehicles they are compatible with.

'make model (what is is)' as first 3 words in all questions. https://www.google.com/search?q=demo+mode+the+code+for+4.91 ..

Unfortunately, no one knows or is telling. Companies rarely state power in RMS because Peak Power is a much more impressive. 1000 watt amp, 200 watts RMS x 2 channels at 8 ohms. Look for a sticker on the unit. https://www.google.com/search?q=Xplore+Amp+5553 ..

I have the disc if you still need it

I think this is an old Blaupunkt where the code cannot be calculated using the serial Number.
It will require specialist advice . Try asking here for free advice....CLICK HERE Mention FixYa

https://www.scribd.com/document/402088377/pioneer-deh-2700-pdf this is a service manual you can download or scroll through. Hope this helps. There is also a schematic here.

I respectfully suggest reading the manual that is available online and at the point of purchase for an accurate assessment.

As used in 2013 Honda Pilot? https://www.google.com/search?safe=off&rlz=1C1QJDB_enCA643CA644&sxsrf=ALeKk01V_jKjIwXe6-iL48YYBgrjQpYLYA%3A1613496601626&ei=GQEsYO3aJZKE5wL38aDoBw&q=gathers+vxm-164vfi+english+manual ..

To reset a Kenwood 8070 receiver without a remote, you typically need to locate the reset button on the device itself. This button is often small and recessed, so you may need a paperclip or a similar tool to press it. Consult the user manual or look for the reset button near the power or input/output ports on the receiver. Once located, press and hold the reset button for a few seconds until you see the receiver reset. Keep in mind that this process may vary slightly depending on the specific model of the Kenwood 8070 receiver.

Hello! I need my BECKER BE7955 serial number: 65009737!

Bill, did you ever figure your issue on your "no sound" problem? I'm having the exact same issue with a used car I bought that has this same stereo in it. CD plays and has sound, tuner shows its on but no sound. ????

1. Mechanical Issue: There might be a mechanical problem with the disc drive or the eject mechanism. It's possible that a part is jammed or not functioning correctly.
2. Dirty or Damaged Disc: If the disc is dirty, scratched, or damaged, the player may have difficulty reading it and thus not ejecting it properly.
3. System Error: There could be an internal error within the player's software or firmware causing it to not recognize the disc properly or to malfunction when attempting to eject it.
4. Power Issue: Sometimes, power-related issues can affect the functionality of electronic devices. Ensure that the player is receiving adequate power and there are no loose connections.

Here are some troubleshooting steps you can try:

• Turn off the player and then turn it back on to see if it resolves the issue.
• Try ejecting the disc using the manual eject button (if available). This button is usually a small pinhole near the disc slot. You can insert a paperclip or a similarly sized object into the hole to manually eject the disc.
• If possible, try using a different disc to see if the problem persists. If other discs work fine, then the issue may be with the original disc.
• Check for any visible obstructions around the disc slot and remove them if present.
• If none of the above steps work, you may need to contact Alpine customer support for further assistance or consider taking the player to a qualified technician for repair.

What is your question? Thank you.

no clue not english

A few options: You can contact the manufacturer, VOXX Electronics, by phone at 1-800-645-4994 or by email at [email protected]. They may be able to provide you with the accessories you need or direct you to an authorized dealer. You can visit the VOXX Electronics website and look for the XR1020U model, which is the same as the XR1020 but with a universal trim ring. You can find the list of accessories and their part numbers on the product page. You can then order them online or call the customer service number above. You can search for the accessories on online marketplaces such as eBay, where you may find new or used items for sale by other users. However, you should be careful to check the seller's ratings, reviews, and return policy before making a purchase.

When the unit was in the Mazda, it was run and monitored by the Body Control Module computer. Moving dedicated units from one vehicle to another seldom works the way you expect. https://www.google.com/search?q=pioneer+ca9pa+v6+650+wiring+diagram ..