Water Sport - Popular Questions, Answers, Tips & Manuals
I have a sportsstuff speedzone 2 tube with a slow leak in the main bladder. Can the bladder be removed to fix?
Yes, the bladder of a Sportsstuff Speedzone 2 tube can be removed to fix a slow leak. To do this, you will need to locate the valve that inflates the bladder and remove it from the tube. Once the valve is removed, you can carefully pull the bladder out of the tube and locate the source of the leak. Depending on the size and location of the leak, you may be able to patch it with a repair kit or you may need to replace the entire bladder.
It is important to note that removing and repairing or replacing the bladder can be a difficult and time-consuming process. If you are not comfortable doing this yourself, it would be best for you to take your tube to a professional repair shop.
7/13/2019 2:29:10 PM •
Sportsstuff...
•
21,266 views • 0 helpful votes
I’m trying to buy a new bathing suit. According to the size chart my bust and hips are one size and my waist is another. Do I go with the bust and hip size? Thank you
Lots of ladies share your problem which is not easily overcome, especially if your waist is larger rather than smaller...
You really need to try on several costumes to find the best fit and in the lower price ranges you are likely to discover considerable variation between garments of the same theoretical size.
This is because the fabric tends to be cut to a tolerance rather than an exact size.
If your waist is smaller I suggest you choose a garment that provides the best fit for your hips and bust but if your waist is larger, practically speaking, you will have little choice and will need to buy to suit your waist and either compromise on the bust/hip fit or have a seamstress make a few slight alterations.
Good luck!
4/6/2018 2:39:25 AM •
Water Sport
•
566 views • 0 helpful votes
I have a 1999 yamaha
You must try to crank it by hand ,remove spark plugs so there will be little compression and then try to turn the motor it should turn without to much force this will indicate the motor has not seized when hooking up a jump start do not connect both leads directly to the battery ! the red + lead should connect to the red+ on both batteries but the neg lead - should not go to the battery post but to a ground usually directly to the metal engine cover or you can damage the battery !
99 yamaha xl 1200 limited rev problem no speed
if the wear ring is installed wrong or the impeller is full of debris this will be the result. look close at the wear ring for scrape marks from the propeller OR are you missing carpet off the rungs of the trailer ?
7/14/2017 12:54:03 AM •
Water Sport
•
2,364 views • 0 helpful votes
Yamaha waverunner won't idle and losing power
L stands for limp mode
it is a mode that the ECM selects to prevent serious damage to the engine ( from you lack of oil )
have the fault codes read then reset with the scan tool
3/31/2017 6:21:03 AM •
Water Sport
•
4,654 views • 0 helpful votes
How to to find PLA filament for 3d printers
You can contact the store where you purchased your printer. Either you should try amazon store to collect your 3d printer parts. Specially for PLA filaments you should try
3D Printing parts supplier, because they provide various types of PLA filaments like -
- Ultimaker 2 PLA Filament (
flexible white,red,transparent,blue,ultimate blue and others)
Its asking me to enter puk # whats PUK
PUK ( personal user key) codes are only available from your service provider
It is a code that makes you sim card inoperable if stolen and cuts in after 3 false attempts at you PIN number
call them on another phone provide proof that you own your account and they will give it to you
Vw battery light on
Alt. Is bad pull battery's terminal off while car is running if it dies the alt.needs replaced
1/11/2016 7:14:52 PM •
Water Sport
•
662 views • 0 helpful votes
Not finding what you are looking for?