Blenders - Recent Questions, Troubleshooting & Support


Fixya does not sell VillaWare parts.

VillaWare... | Answered Yesterday


It Could Be a Number of Things..
It's most likely that the electrical Wire Could Have a Shortage, If it cuts off again Try gently Wiggling the Electrical Wire in a Number of Directions If it cuts on and off while your fidgeting with it, you've found your Problem! A quick fix would be to Adjust the wire In the position it would cut on the strongest, wrap the cord with Tape to Keep the wire in that Position, this will Prevent it from shorting again.
Either that or you simply put too much product in the Blender with an inadequate amount of liquid.

Blenders | Answered on Oct 06, 2019


Why do you need to get into it? All Braun products have locking clips along the split edge. You need to use a plastic 'bludger'. Better to take it to a Braun Service Centre.

Braun Blenders | Answered on Sep 16, 2019


typically, you can't repair it.

Blenders | Answered on Sep 14, 2019


that would be a function of the container. Just a guess, why would it not handle hot & cold? Obviously if it were glass I would say yess. If plastic contacts the liquid, then maybe/maybe not.

Moulinex... | Answered on Sep 14, 2019


it is probably covered in your manual. They are all slightly different.

Hamilton Beach... | Answered on Sep 14, 2019


If you think you need to replace it, first make sure you can get the part.
then look for a parts breakdown at an online parts store. If that doesn't help you will have to hunt and peck to figure it out. Do not be too aggressive, though after all these years things will be stuck.

Waring Blenders | Answered on Sep 14, 2019


that happens to the best of them. Try heat soap, vinegar, and a tight grip to get it off.

Blenders | Answered on Sep 14, 2019


blenders are:
power cord, switch, speed control, and motor.
A disassembly and VOM meter is required to determine which part is defective.

Blenders | Answered on Sep 14, 2019


Hiya,

Sorry to hear you are experiencing an issue with your blender. We believe that the described issue indicates control board fault.

If you have KSB555, please follow the link below to show you how to replace this part on your appliance.

https://www.kaparts.co.uk/Help/KitchenAidHelp/KitchenAidBlenderHelp/HowtochangetheControlBoardonaKSB555/tabid/650/Default.aspx

https://www.youtube.com/watch?v=Lafh8UGn4No

Hope you found this useful :-)

KitchenAid... | Answered on Sep 12, 2019


how to tighten nut on kitchen aid blender

KitchenAid... | Answered on Sep 12, 2019


Use https://www.google.com and the words manual and whatever manufacturer and model it is to see manuals.

Blenders | Answered on Sep 11, 2019


Replace the potentiometer with a better one. Do not use the CHEAP PIECE OF CR@P that comes with the blender. For what they charge for these machines, they should be using MUCH better components. I used part RV4N502C-ND from Digi-key as described by another poster for a different model. The knob didn't fit, so I also used Mouser part #5164-1500 knob, which look exactly the same.

Vitamix 5000... | Answered on Sep 10, 2019

Not finding what you are looking for?
Blenders Logo

6,195 questions posted

Ask a Question

Usually answered in minutes!

Top Blenders Experts

eyecam

Level 2 Expert

96 Answers

Marvin
Marvin

Level 3 Expert

85178 Answers

Ross Keen

Level 3 Expert

1351 Answers

Are you a Blender Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...