Bosch Washing Machines - Page 3 - Recent Questions, Troubleshooting & Support

Had a repair man here for the same issue. Learned two things:

1. Too much detergent causes 'soap lock.' The electronics will get confused when there's too many suds left after a rinse and shut the spin cycle down. That's why re-running the entire cycle without more detergent solves the problem. Use less detergent.

2. There is a way to manually get the spin cycle to run using diagnostics codes. Here's what my guy did:

a. Washer selection knob in OFF position.
b. Hold the 'Spin Selection' and 'Delay Start' buttons down at the same time.
c. While holding those two buttons, turn the Washing selector knob to Permanent Press-Cold.
d. Keep the buttons held down until the LCD control panel reads 'P:01'
d. Release buttons.
e. Use the 'Spin Selection' button to cycle thru the codes. Stop when it reads 'P:04' which is the spin cycle.
f. Press 'Start/Pause' button to begin the spin cycle.

I don't know what the other codes do but this should save you from having to run the entire wash cycle.

Hope that helps! Tim

There are normally two ways. Disconnect the power for 5 minutes. Keep pressing the Timer button until it goes back to Zero 0 Hours. https://www.google.com/search?q=cancel+timer%2C+Bosch+washing+machine The last video is for a Dishwasher, but may be the same.

Try unpluging it for a couple of minutes

Replacing the door hinge on a Bosch WAT286H0GB washing machine can be a bit tricky. Here are some general steps that can help you put the front and back panels of the door back together:

1. Make sure that all the parts are in the correct place and that the door hinge is properly aligned.
2. Place the back panel of the door onto the front panel, lining up the hinge with the corresponding holes on the back panel.
3. Insert the hinge pins into the holes on the back panel and ensure they are securely in place.
4. Secure the panels together by tightening the screws.
5. Check that the door is operating correctly and that there is no wobbling or loose feeling when you open and close it.

It is always important to refer to the manufacturer's manual for specific instructions on how to fix the door hinge on your Bosch WAT286H0GB washing machine. If you are still having trouble, it might be a good idea to seek the help of a professional repairman.

https://www.bosch-home.com/us/experience-bosch/heart-of-the-home/tips-and-tricks/all-articles/e24-error-code

F8 is not a common error code for a washing machine, so it is likely specific to the brand and model of your washing machine. Without more information on the brand and model of the washing machine, it is difficult to provide a specific solution. However, if you are seeing the F8 error code on your washing machine, the first thing you should do is consult the manual or check the manufacturer's website for the specific meaning of that error code. The manual or the manufacturer's website should provide troubleshooting steps specific to the error code. If the problem persists, it's best to contact the manufacturer or a professional technician for help. They will be able to diagnose the problem and recommend the appropriate course of action. It's important to note that F8 Error can be caused by various issues such as a faulty sensor, control module, door lock, or wiring, etc. It's best to get it checked by a professional technician

Hi.

Here manual : BOSCH WVF2000 Washing Machine.PDF

Here parts manual : WVF 2000 Bosch-Spares.pdf

Regard

Hi, please verify with the product documentation that the flashing-door symbol indicates what you've initially mentioned. Apart from that, you might look for the sensor and hold it in to temporarily overcome the issue. If the door being shut is the issue, pressing in the sensor should fix the issue for you temporarily. If not, then you can work with Bosch or Home Deport to moving forward. Prior to their arrival, you can power cycle your machine 1 or 2 times and check for the door symbol once more. It could be that they sensor has gone bad for some reason. Thank you

That sounds like a failed control board. You need dealer service.

Any of these. It is just water in, water out and two power wires. Look for one the same shape. You may be able to swap the mounting bracket over, or just drill new holes in the case. https://www.google.com/search?q=Hot+water+inlet+valve+00171295 Having said that, the part is here! https://www.repairclinic.com/ProductDetail/989550 https://www.google.com/search?q=Bosch+washer+wfk2401uc+water+inlet+valve ..

i think i would remove the outlet pipe take it to a yard water spicet and pressure blow it out to be sure it's clear then i would check where it connects on both ends to be sure those are clear then put it back together run it one cycle (empty) and see what happens.. it's also possible that the problem is from the screen in the water line going in.. being partially stopped up ... but i'm betting on the drain line.

Hope this helps there's a repair video..... https://www.appliancepartspros.com/bosch-belt-blower-154142-ap2805440.html

Hi, Please make sure that your laser-distance measure is charged properly to start. View it's screen for any listed error codes that could give us a clue to watch the issue is. If the error code hints at restarting the device, then we can move in that direction. If the error isn't revealed from perusing any troubleshooting documentation that comes with your device, then you can reach out to Bosch for repair/replacement help. Thank you.

Question edited for clarity, add words, make sentences and stuff. https://www.bosch-home.ca/en/service/get-support/error-e23-or-f23-washing-machine https://www.google.com/search?q=bosch+series+8+washing+machine+e23 ..

Disconnecting the power will normally release the latch.

Bosch washer error code f43 : Causes, How FIX Problem

https://all-errors.com > bosch-washing-machine-error-c... What does the F43 error mean in Bosch washing machine? It indicates that the motor does not rotate or something blocks the drum. What is the main sign, by which ...

Me too. What a piece of trash this washing machine is

Had a E90 fault,bosch condenser dryer found if I disconnected pump plug on the pcb mounted rear rhs of machine, rear connector with 2 red wires, fault would not be present and dryer would run, removed pump cleaned, and spun by hand, reassembled and operated correctly

Go to appliancepartspro.com enter your model numer and it will give you every part you need in diagram pictures.