AEG Washing Machines - Recent Questions, Troubleshooting & Support


Maybe it helps something
https://www.manualslib.com/products/Aeg-Bs-45-3977008.html

AEG Washing... | Answered on Mar 02, 2019


test you water solenoids and replace if faulty

AEG Washing... | Answered on Feb 28, 2019


http://bastlman.wz.cz/2010/08/AEG-Lavamat-error-codes.html

AEG Washing... | Answered on Feb 08, 2019


This could be the valves not opening all the way that could be due to mineral buildup, check the water pressure in the line and also check to make sure the proper voltage is getting to the valves and if all is ok, replace the valve assembly from any online spares centre.

AEG Washing... | Answered on Feb 03, 2019


Power supply problem. Try another plug in. If it still doesnt work you have a wiring problem.

AEG Washing... | Answered on Jan 31, 2019


USUALLY THEY JUST PULL OFF . WITH SOME RESISTANCE OF COURSE , OTHERWISE THEY WOULD JUST FALL OFF

AEG Washing... | Answered on Jan 24, 2019


Cd - means door lock defect so replace door lock or check cable and PCB (triac).

Dado

AEG Washing... | Answered on Jan 12, 2019


C1 - means that in prewash cycle no water inlet, valve does not open/ interruption or flow rate too low.
So I suggest to you following: check water inlet, clean sieve, check inlet valve, check pressure sensor and finally check wiring.

Dado

AEG Washing... | Answered on Jan 12, 2019


If there is a fault happend the error code should appear on the display (as shown picture below) :

error code will appears on display-x2i5s4yosfxg1xpsbuvvkqua-1-0.jpg There are two types of error code, first one that begins with a letter "C" and a mean customer fault code that can eliminate by the customer.
for example:
C1 - means "Telescopic runner inside during pyrolyse"
Remedy: "Remove side grids during pyrolyse"

Faults that begin with letter "F" require the expertise of a service technician especially when it comes to new ovens powered and controlled by electronics.

for example:
F 239 means: Quantum Touch Controller alarm:
1. If the communication over the bus SPI with the Quantum touch is after 50 trials unsuccessful than alarm is set. The alarm is reset if the communication is okay again.
Could be:
1. Connections Board Touch.
2. Board Touch fault.

Dado

AEG Washing... | Answered on Dec 30, 2018


turn Programswitch to ‘OFF’ -
press first 2 buttons (1 and 2) Keep it pressed turn programswitch 1 klik to the left (against the klok)
all LED’s lights up.
realise the buttons
turn progam switch to off

youre machine is now reset

if problem comes back, carbon brusches on the motor are defect.

AEG Washing... | Answered on Dec 24, 2018


Hallo, my AEG lavamat 41280 update gives E20 warning, what should I do? Thanks

AEG Washing... | Answered on Dec 16, 2018


check with any local appliance store we have no clue what is available

AEG Washing... | Answered on Nov 09, 2018


To display Error Code:
Move Programme Selector to the Off postion.
Press the 2 buttons on the right and turn the selector 1 position clockwise and hold the 2 buttons for about 5 seconds until all the lights are flashing. Release buttons and turn the selector to the 10th position. The Error Code will be displayed.
Note the code then turn the selector to off ,then on,then off again.

AEG Washing... | Answered on Nov 01, 2018

Not finding what you are looking for?
AEG Logo

1,511 questions posted

Ask a Question

Usually answered in minutes!

Top AEG Washing Machines Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18429 Answers

mikenearman

Level 2 Expert

127 Answers

jimorris77

Level 3 Expert

411 Answers

Are you an AEG Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...