Trying to set time - Nixon Lodown Watch

1. Buttons on the Device: Look for any buttons on the device itself. Sometimes, there are buttons that allow you to navigate through menus and adjust settings directly on the device.
2. Trial and Error: Try pressing different buttons on the device to see if any of them bring up a menu for setting the time. Look for buttons labeled "Menu," "Setup," "Clock," or similar.
3. Long Press: Sometimes, pressing and holding certain buttons on the device can activate different functions. Try pressing and holding various buttons to see if it triggers a menu for setting the time.
4. Google Search: If you know the model number of your Ultech device, try searching online for the manual. Many manuals are available for download from manufacturer websites or other online sources.
5. Contact Manufacturer: If you're unable to find the manual online or if you're still having trouble setting the time, try reaching out to Ultech's customer support. They may be able to provide you with guidance on how to set the time on your device.
6. Replace Remote Batteries: If the remote isn't working, try replacing the batteries. Sometimes, a non-functional remote can be as simple as dead batteries.

It sounds like you are having an issue with setting the time on your Ott light. Here are a few suggestions that may help you resolve the problem:

1. Check the owner's manual for your Ott light. It should have instructions on how to set the time and troubleshooting tips for common issues.
2. Make sure that the light is plugged in and the power is turned on. If the light is not receiving power, the time cannot be set.
3. Check the batteries in the remote control. If the batteries are low or dead, the remote may not be able to communicate with the light and the time cannot be set.
4. Make sure that you are pressing the correct button on the remote to set the time. Some Ott lights may use a different button or sequence of buttons to set the time.
5. If the light is still not responding to the remote control, try resetting the light by unplugging it and then plugging it back in. This may reset the light and allow you to set the time.

If you have tried these steps and are still having trouble setting the time on your Ott light, you may need to contact the manufacturer or a customer service representative for further assistance. They may be able to provide additional troubleshooting tips or repair the light if it is experiencing a hardware issue.

You have to press the clock symbol before you try to set the time. Once you set the time then you can press the start button and all will be well

how to set time on a citizen eco drive wr2

Click on my profile (escapement), then click on Tips and Tricks. There you will find link to B&M watch manuals.Rate me, please

try changing the battery.

First look for the set button then press it ,a long press and If it is blinking that's the time you to select the hour ,the minutes,the day/date,the alarms and the special features of your watch.The right button the up and down or for scrolling.Try all of this so your time will set.

Hope it may help you;

Regards;
VOTIT DON'T FORGET TO RATE

Mike 1935 if your watch has hands only & no digital display the crown where you set the watch pulls out half a click to set the date and should pull out a little further to set the time try that.

bjbc I am assuming your seiko watch is a digital watch. Try holding in the top rt button if its the watch I think it is it should change to 12yr time.

I have a G Shock DW-004 made in 1997. I had this same problem, and I tried everything to change TO military time and back to standard time. I just read the bit to try and was about to do it. I pressed the top left button to get the time to flash, and hit the light button by accident (the one with the big G on it) and VIOLA! It changed to military time. So in my model, anyway, the G light button (under the display on the edge of the watch body) changed the time to military from standard and back again, when the time is flashing.

Good luck!

Try this method. Set the date until it reads a couple of days in the past and then set the correct time. Of course do not touch your date or time settings between the hours of 9PM-1AM. Wait until the next day, then move the hour hand forward until you reach the current date with the correct time.