Trying to connect digital audio output optical terminal to existing analalogue hi-fi amplifier

Hi, the fisrt step is to connect a toslink cable from TV output to an amplifier with optical input, or if your amplifier has only analog audio inputs (RCA red and white connectors), you have to use an digital to analog converter device. After cables are connected, usually you must change which type of audio connection you will use in TV menu, in audio options.

If you are connecting the soundbar to your TV with the digital audio cable, make sure to select "D IN" using the source button on the soundbar. Bluetooth (BT) is a separate source from another device. (phone, etc.) The TV will need to be set to use the digital audio output and probably PCM format. (?) The subwoofer is preconfigured at the factory to mate up with your soundbar. (See below instructions - your soundbar includes the amplifier:)

Digital audio output setting:
After connecting an amplifier with digital audio input and
external speakers as shown, you should set an audio
output format compatible with the programme you are
watching or the device connected.
Go to "HOME" > "TV Menu" > "Setup" > "Option" >
"Terminal setting" > "Digital audio output" > select
"PCM" or "Bitstream".
NOTE
• When set to "Bitstream", Dolby Digital is output when the Dolby
Digital or Dolby Digital Plus audio formats are received. When
set to "PCM", PCM is output no matter what audio formats are
received.
• When set to "Bitstream", HE-AAC audio formats can be output
as Dolby Digital.

flat pannel tv's do not have speaker output but some have rca audio output which are connected to an amplifier and the amplifier to your speakers
Look for audio out sockets on the rear pannel..

Len

The only digital audio input for this TV will be via the HDMI input. Of course, even with HDMI in, you're only going to get a simple stereo output from the TV. You can use the analog L & R audio inputs for a very similar sound from the TV speakers.

The digital multi-channel audio (Dolby Digital, THX, 5.1, 7.1, etc) encoded in the program should be connected to a suitable multi-channel amplifier with either a TOSLINK (optical), RF (coaxial) or HDMI cable for theatre-like sound. This can be done by (a) cabling from the source (DVD, BluRay Disk, Set Top TV Tuner, etc.) directly to a multi-channel amp and speakers, or (b) from the HDMI output of these devices (DVD, BluRay Disk, Set Top TV Tuner, etc.) into one or both of the TV's HDMI inputs. This will provide only stereo sound output from the TV speakers. You should connect the TV's TOSLINK optical "Digital Output" jack with an optical cable to the amplifier's TOSLINK optical input jack to obtain theatre sound.

To listen to the program shown, you would select the amplifier input assciated with the optical, RF or HDMI input that is connected to the source (DVD, BluRay Disk, Set Top TV Tuner, etc.) if connected directly. If the TV HDMI input(s) are used, they are output to the TV optical output and should be connected to the amplifier optical input. The amp input associated with the optical input should be selected to hear the program with theatre-like sound.

yes.....connect to digital audio output.........optical fiber optic cable needed.....connect to digital audio input on hi-fi.......select pcm as format............good success, meder's tv service

try this , i think it will help,
http://resources.jvc.com/Resources/00/01/13/YA590ien.pdf

best regards

Most of the TVs are having an analog audio or digital audio output.
However, it is not possible to connect direct speakers to it.
It is required to use an amplifier/receiver to connect the speakers..
You can also connect PC speakers (like 2.1 and 5.1) using a compatible cable as it has built in amplifier.
Please get back to me if you need further assistance. www.fixya.com/users/shajanrs

hi,
u can connect the digital audio output (optical) to ur av receiver or any amplifier wich have a digital audio input(optica).
ok

hi,
you can connect th analog audio output of your tv to ur preamp's any of the analog audio input, if it is a stereo preamp. if u have a AV receiver, then connect the digital audio output ( optical )of your tv , to any one of the digital input of ur AV receiver.
ok

I don't expect a 2 channel amp would have a digital input such as optical. More likely you would be able to pull analog stereo (red and white RCAs) off the Panasonic and run to the JVC.