My washing sent in control panel alarm is ( EHO) what problem model ( zanusssi zwf 16581w)

Page 9 of this manual, if this is the same model, may help turn off acoustic signals. It shows an image of a P and another image of a button to turn off.

https://manuall.co.uk/zanussi-zwf-91483-wr-lindo-300-washing-machine/

The EHO (or EH0) error indicates a problem with the incoming power or an electrical problem inside the washer. Unplug the washer for a while to reset the error code. Next check your wiring and make sure that the outlet doesn't have a fault. If you live in an area with brown-outs or wires that touched during a storm, wait until the electricity is repaired. Then check if the power supply to the washer was damaged by the surge or changing power levels.

If these aren't responsible for the problem, you'll need to check the wiring for shielding damage, the wire harnesses and the rest of the washer. There is a parts diagram here: http://docplayer.net/60693214-Spare-parts-list-household-washing-machines-pnc-elc-brand-model-market-electrolux-ewf10842-th-washing-machines-front-loaded.html .

I hope this helps.

Cindy Wells

The power supply is failing and needs to be replaced but first try the steps provided in the link below. Washing machine displays error message EHO EH0

If you need further help, reach me via phone at https://www.6ya.com/expert/steven_a67ead41eb5fc62a

This causes a water leakage, which flows inside the bottom of appliance, thus switching on the Aqua Control sensor and generating alarm EF0/EF3.

Be sure to find water leaks and repair the defect.
Incline the washing machine of about 10 cm to spill the water, so that the sensor can operate normally again.

Dado

most probably the solenoid valve that controls the draining is stuck and the water has not drained from the previous cycle or so the machine thinks.
You need a replacement of solenoid valve.

Possible defective washer control panel.

Hello,

First of all is the machine doing anything it should not be.That alarm code does not exist on our system,the closest is EH1 and this relates to Power supply problems or a faulty PCB.To cancel press and hold the start/pause button and the nearest option button for about 5 seconds,now turn the programme knob to position 10 then hold in the start/pause button and option buttons again till alarm disappears and E00 is showing.Then turn dial to 0 then back to position 1 then back to 0 to cancel operation.

Hope this helps.

hi follow this Step 1: Unplug the washer. To access the timer, remove the control knobs and the panel that covers the controls. This may be a front panel, or access may be through a panel at the back of the unit. Carefully examine the wires that connect the timer to the other parts of the washer. If the wires are loose or disconnected, try pushing them into position; they usually fit into their terminals like plugs. Use long-nosed pliers to avoid breaking the wire connections -- never pull a wire by handStep 2: To test the timer, use a VOM set to the RX1 scale. Disconnect the power leads to the timer and clip one probe of the VOM to each lead. The VOM should read zero if the timer is working. Since the timer is a multiple switch, turn it through its cycle and test each pair of terminals in turn. The meter should read zero at all of these points. If one or more readings are above zero, the timer is faulty and should be replaced.
Step 3: To replace the timer, unscrew and disconnect the old one. Install a new timer made specifically for the washing machine. If there are many wires on the timer, have a helper hold the new timer next to the old one as you work. Disconnect the old wires one at a time, connecting each corresponding new wire as you work, to make sure the connections are properly made. Or, draw a diagram showing the connections before removing the old timer. After all the wires are connected, check the connections again for correctness and screw the timer assembly into place.
thank u.......................

clean out filter, door bottom right, unscrew filter and clean it

It is'nt any adjustment on those machines. They were fitted with eleastic belts. Is the belt not tight enough, you need a new belt.