I've just bought a second hand MP160,which I only intended to used as a scanner.
I can't get the scanner to operate due to an E5 error on the display,and a 2,114,0 error which appears as a pop-up when I attempt to scan.
Although empty,the cartridges are of the correct type and are seated properly.
When I remove the cartridges completely the error codes do not change.
Is an empty cartridge enough to cause this issue?
Many thanks.
I got this Error 2,114,0 with my MP210 and none of the above fixes worked. This is how I have got it working again: Press and hold the maintenance (picure of spanner and screw driver) button and the reset button ( Inverted red triangle) together for five seconds or more. The flashing error code 1 and 6 will then stop flashing and replaced by a print copy no 1. The printer/scanner is reset and the scanner works.
sooooooooooo many thanks bro, it works!!
It's 2018 and this worked for my MP160 – thanks!
×
Unloading and re-installing the drivers did nothing. Same results after a complete removal and uninstall. I suspect it may have something to do with the Canon call-back program OR the chip feature used in the cartridges after the cartridges have been refilled a certain amount of times.
Canon, Epson, HP and Lexmark ALL use this feature in an effort to deter owners from being able to save money using re-manufactured cartridges that run fine or even better than the factory issued ones.
Hi,
CANON PIXMA MP160 All-In-One InkJet
Printer has few common problems. Such as Driver CD
lost, Scanner does not work, Connection problem etc. For find all these software solution
just click here....
http://www.canon.com/printer/prob676ijt65/solution
533
Thank you a lot mdhasan :) we could not find out how to get rid of that error :) if you also need something write to me :)
Jan - [email protected]
×
Hi dear
this the error code
E9 The connected digital camera / video camera does not support Camera
Direct Printing
E14 The Ink cartridges whose destination are wrong
E15 Ink cartridge is not installed E16 - Ink remaining is unknown
E16 -E19 Failed to scan head alignment sheet
E22 Carriage error
E23 Paper feed error
E24 Purge unit error
E25 ASF(cam) sensor error
E26 Internal temperature rise error
E27 Waste ink absorber full or platen waste ink absorber full
E28 Ink cartridge temperature rise error -
E29 EEPROM error
E33 Paper feed position error
E35 15 USB Host VBUD overcurrent error - USB
E37 17 Abnormal motor driver error
E40 20 Other hardware error
E42 22 Scanner error
E2-2 No paper (ASF)
E3-3 Paper jam
E4 No ink
E5-5 The ink cartridges are not installed or a non-supported ink cartridge is installed ,
or the ink cartridges are not installed properly
E8 Waste ink absorber full, or platen waste ink absorber full
First, download the software at http://www.box.net/shared/4yblbn34kg
Secondly, to run the software your printer has to be in service mode. Do that by
- unplug cable
- press and hold "power" button
- plug cable
- press "resume" and release
- release the "power" button
At this stage, your computer will detect a new hardware
Run the software.
oke
Steps to troubleshoot the Printer Error Code E5 and E8:
Step1: Place the HP Printer over a durable workbench, possibly in a well-lighted and ventilated area. You will be needed a screw driver, a clean rag and alcohol.
Step2: The main printer cover need to be opened and the smaller inner over.
Step3: Unlock the ink cartridge lever, hold the handle and pull it out.
Step4: Look for the printer roller, unclip from the holder.
Step5: The roller need to be hold and clean with the rag damped with alcohol, allow it to dry. The thorough cleaning is needed to remove dust, accumulated ink and other substances that coat the surface.
Step6: Clip the roller back to the printer holder, correct the reinstallation to produce a distinct click as the roller sets into position.
Step7: Turn the printer sideways and look for the jack at the back, remove the two nuts and pull the jack out.
Step8: Clean the black HP Printer roller inside and all the other parts, then reinstall back the jack using the nuts previously taken out.
Step9: Reinstall the ink cartridge back lock the lever down to hold it securely.
Step10: Close the printer and power up. If the error lights still blink, open-up the scanner cover and look for the drive gears.
Step11: Apply oil on the drive gears and close the scanner.
Step12: Power-up the printer again.
When you have completed the above steps in resolving the error E8 of HP Printer and came across the problem you must get in touch with http://www.canonprintersupportnumbers.com/
1-800-213-8289(toll-free).
Canon Printer Support Phone Number 1 8002138289 Tech Support
Canon Printer Support Phone Number 1 8002138289 Tech...
canonprintersupportnumbers.com
Canon Printer Technical Support...
How to use it??!!
Have you tried reloading the driver for the mp160 off canon's website
sometimes that helps the problem
I had the same problem when i first refilled my ink cartridges, i kept on removing the ink cartridges and installing them again, it worked for about a month or two, so first make sure the ink cartridges are placed correctly
Now, i have the same problem again, the easy solution is to replace both ink cartridges, make sure they are canons original ink cartridges.
You can also diagnose which ink cartridge is making the problem by installing one ink cartridge, then read the error message, if both ink cartridges are unrecognized most probably it caused the problem, then try with the other one, if also both arent recognized then it is damaged too, both will need replacement. If one of them is recognized in this procedure then the one recognized is okay.
For me, the colored ink cartridge is making the problem, when both ink cartridges are installed, they arent recognized, when i remove it, the black alone is recognized, i replaced the colored ink cartridges and the printer is operating normally
btw, the problem is in the connectors, they get worn upon usage, or the chip inside the ink cartridge, if the ink is low inside it and you keep on printing the ink will no longer be available to cool the chip and this will burn it, rendering it as unrecognized
hope that helped
Greeting from Jordan
Wath?
SOURCE: E5 and 2,114,0 errors on Canon MP160
press resume botton for ten seconds or more the mp210 will work
SOURCE: E5 and 2,114,0 errors on Canon MP160
Empty cartridges may cause this error. Here is the error code list for your printer
E2-2 = No paper (ASF)
E3-3 = Paper jam
E4 = No ink
E5-5 = The ink cartridges are not installed or a non-supported ink cartridge is installed, or the ink cartridges are not installed properly
E8 = Waste ink absorber full, or platen waste ink absorber full
E9 = The connected digital camera / video camera does not support Camera Direct Printing
E14 = The Ink cartridges whose destination are wrong
E15 = Ink cartridge is not installed E16 - Ink remaining is unknown
E16 -E19 = Failed to scan head alignment sheet
E22 = Carriage error
E23 = Paper feed error
E24 = Purge unit error
E25 = ASF(cam) sensor error
E26 = Internal temperature rise error
E27 = Waste ink absorber full or platen waste ink absorber full
E28 = Ink cartridge temperature rise error -
E29 = EEPROM error
E33 = Paper feed position error
E35 15 = USB Host VBUD overcurrent error - USB
E37 17 = Abnormal motor driver error
E40 20 = Other hardware error
E42 22 = Scanner error
If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe
I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309
36,916 views
Usually answered in minutes!
Getting error message 2,114,0 when trying to scan. Also error message E 5 when trying to print. Cartridges are in properly, has been printing and scanning until now, yet no changes I'm aware of.
My printer is not working and displays a blinking E 2, what does this mean? and how do i fix it.
i have the same problem
Having the exact same problem. The window that pops-up says"Printer maintenance in progress. Scan after it is complete. Code 2,114,0".
Alternating "e" and "5" appearing on the yellow LED readout as well.
I'll try reloading the drivers but this is ridiculous!
When i try to scan a document this message comes up"printer maintence is in progress. Scan after it is complete.Code: 2,114,0
How do i fix this please? I have tried changing the connection cables
I have a canon mp 210 with the same problem. I tried to switch it off for a long time .
i have same problem with canon pixma 510. no ink cannot use scanner!!!
why not. what has scanner to do with ink!!! tep
probleme e 5 canon mp 210
Canon MP600, used as scanner and kopier and printer; now I can't get the scanner to operate due to error on the
display, 2,114,0 error which appears as a pop-up when I attempt to
scan.
Although full cartridges are of the correct (canon original) type and are seated properly.
When I remove the cartridges completely the error codes do not change.
i bought a new cartilge for mp160.. black. it run for a while and later displayed E 2,E 7. PLEASE Help.
and the cartileges cant move to the copying or printing postion.
Please the solution canon MP !60 blinking code Error E5. Thank's
i have exactly the same problem onmy mp160
emy canon indicator e5
por favor neecesito ayuda error E 5 mp 160
scaner problem no function
-*-
when i want to scan a document i see a message told me to wiat the printer to mentenanc
I have just replaced the ink cartridges for my MP210 and its telling me they are not seated correctly and they are, what do i do.
I've just bought a second hand MP160,which I only intended to used as a scanner.
I can't get the scanner to operate due to an E5 error on the
display,and a 2,114,0 error which appears as a pop-up when I attempt to
scan.
Although empty,the cartridges are of the correct type and are seated properly.
When I remove the cartridges completely the error codes do not change.
Is an empty cartridge enough to cause this issue?
TENGO UNA CANON MP 160, Y ME APARECE E 5 EN COLOR NARANJA CUANDO LA ENCIENDO, Y APARTE CUANDO VOY A ESCANEAR ME SALE ERROR 2114.0 Y ME DICE QUE DEBO TERMINAR LA FUNCION QUE EMPESE.
YA REALICE EL PROCEDIMIENTO DE APAGAR Y OPRIMIR STOP A LA VEZ PERO NO ME FUNCIONA
este total blocata si nu imi recunoaste cartusurile
somebody told me that there's a software can used to fortified the counter memory file of the canon printers which control the usage of used cartridge, this will help us to save more money than buying expensive new cartridges with ink. we can download it.
×