Door Locked after FA code

Press cancel button twice and restart

Inspect the water level pressure switch tube, run diagnostic cycle, and see if there are any stored error codes... make your repair plan based on the codes.

Press the cancel button twice to cancel the error code. There should be an error code flashing -- for example 'F02'.

Hi,
This error code means"No water detected entering machine or Pressure switch trip not detected".

Is the machine getting any water? Check that the water supply is turned on.
Press pause cancel twice to clear the display.
Try to run another cycle.
Let me know if I can help with anything else.

F/02 Long Drain
If the drain time exceeds 8 minutes, the water valves are turned off and "F/02" is flashed.
NOTE: After 4 minutes the "Sud" error will be displayed, then 4 minutes later the F02 error code will be displayed.

Press PAUSE/CANCEL twice to clear the display.

• Check the drain hose and make sure it is not plugged or kinked.
• Check the electrical connections at the pump and make sure the pump is running.
• Check the drain pump filter for foreign objects.
• If the above does not correct the problem, replace the pump

02 means = Long Drain

If the drain time exceeds 8 minutes, the water valves are turned off and "F/02" is flashed.

NOTE: After 4 minutes the "Sud" error will be displayed, then 4 minutes later the F02 error code will be displayed.


Solution -
Press PAUSE/CANCEL twice to clear the display.

• Check the drain hose and make sure it is not plugged or kinked.
• Check the electrical connections at the pump and make sure the pump is running.
• Check the drain pump filter for foreign objects.
• If the above does not correct the problem, replace the pump.

Press and hold "end of cycle" button for 3 seconds, on the right side of panel. Wait for 2 minutes before trying the door. This is the child lock feature, do it again & it locks.

If helped, pl rate me good!!

Activate the diagnostic test mode.
1. Within 5 seconds, press more time-less time-more time-less time.
2. All indicators should now be on and "88" displayed.
3. Press dryness level button. All LEDs in group should turn off.
4. Press control on button. Control locked should turn off.
5. Open door. Press cancel.

Okay, ther manufacturer recommends unplugging the washer for at least 30 minutes to reset the computer. It could be you have a momentary glitch causing some problems. If you still have the same problem after leaving the washer unplugged, the following link explains the "FH" error code:

http://www.fixya.com/support/r615354-fh_error_code_whirlpool_duet_kenmore

If your clothes are stuck inside and you still cannot get them out because the door will not unlock, you will have to use the manual release to open the door. The next link explains how:

http://www.fixya.com/support/r622155-kenmore_elite_whirlpool_duet_door_jammed

I hope this helps you. If you require additional assistance, please let me know.

Does your front washer, every time you press cancel give you a code that looks similiar to ER?

I checked the description and for some reason whirlpool denies having a F22 code on the Duet, but that doesn't mean much.

I am suspecting several things.

1. Electrical supply may have had a surge at one point or another. You may have to ask your electrical company to put a surge protector on your house by the meter. This is not to protect everything it has its own limits!

2. Unplug the machine for a while. Turn off the water supply and disconnect hoses The machine knows if there is water coming into the machine by a trip sensor.

3. drain out your exhaust line. There is a possiblity your machine thinks you are full of water when it is actually empty.

4 put everything back on, and then plug machine back in after about an hour or so. If it still doesn't work, it is time for your local appliance repair service technician to come out. He will check door trip sensor, and a few other areas that may be acting up.

Good luck.