I subscribed to Jobulator. Ap rings twice and then announces that " job already filled" - all at the same time (over a two-second period). Thus, no jobs. Please advise.

Hello, Carole -

I found your earlier question about the Jobulator app for cell phones. see my answer here.
http://www.fixya.com/support/t26856757-jobulator_will_not_work_phone_steps

Not all everyone's caller information is displayed all the time. Differing telephone systems and central office equipment may not be compatible.

Also, the CID data is sent between the first and second ring - if a ring phone is picked up to soon after the 1st ring, the CID data is not sent - let it ring at least twice.

Lastly, make sure you have subscribed to the service.

Sherry:
I believe that some how the security code #99 got changed. You may want to reset that code as #99 no longer works. From the manual:

Setting a Personal Security Code (PIN)

If you want to be able to play your messages from a remote location, you need to enter a two-digit Personal

Identification Number (PIN) code (01-99).

To select a PIN, perform the following steps:

1) With the phone in standby, press [menu/clock] twice.

The system announces "Security code," and the current PIN code is announced as it is displayed on the base.

Then the system announces the instructions for setting the PIN code.

2) Press [volume/select/ ] or [volume/select/ ] until the desired number appears.

3) Press [set] to select the PIN code. You hear a confirmation tone, then the announcement "Security code"

followed by the new PIN code is announced. After a few seconds, the system announces "To set ring time, press

menu again."
Note: The PIN code is set to "80" at the factory.

This feature lets you know who is calling

without looking at the display.

To use this feature, you must:

- subscribe to a Caller ID service of

your service provider/telephone

company.

- turn this feature on (page 24).

When caller information is received, the

handsets and base unit announce the

caller's name or phone number received

from your service provider/telephone

company following every ring.

The unit announces in English only.

L Name pronunciation may vary. This

feature may not pronounce all names

correctly.

L Caller ID service has a limit of how

many characters can be displayed. If

the caller's name is too long, the

handset may not be able to display or

announce the entire name.

L The announcement is heard at the

same level as the ringer volume (page

16, 23).

L If you turn on the answering system

and set the number of rings "2

rings" (page 36), the unit does not

announce the caller information. If

"Toll saver" is selected and there

is a new message, the unit does not
announce the caller information.

When the AT&T 1717 digital answering machine is powered off it will answer an incoming call after 10 rings, it will announce "machine is off" then beep twice, dial 0 to turn it on. The machine is now ready to answer calls. This 10 ring setting is factory set and cannot be modified. To set the number of rings to answer for normal operation press <SET UP> button and hold for 2 seconds, machine will announce current ring setting. Press and release <ANNC/SKIP> or <MEMO/REPEAT> until you hear the number of rings you want. Press and release <PLAY/STOP> to exit. The ring settings available are 2, 4, and toll saver. When set to toll saver machine will answer after 4 rings when there are no new messages and after two rings when is anew message. Here is a link where you can download manual, http://safemanuals.com/user-guide-instructions-owner-manual/AT%2526T/1717-_E

1) With the phone in standby mode, press the menu/clock key three times.
You hear “Ring time” and the current ring time ([2 ], [ 4], [6 ], [T ] Toll
saver), and it is displayed on the main base. Then you hear the guidance for setting
the ring time.

2) Press the volume/select/ or up or down arrow key until the desired ring time appears.

3) Press the set key to select the new ring time. You hear a confirmation tone, then
the announcement “Ring time” followed by the new ring time. After a few
seconds, the system announces “To set record time, press menu again.”

Need the manual for your phone? You can download/print it here:

http://www.uniden.com/pdf/DXAI5588-2om.pdf

Bill B

Use Ring Select to choose how many times
the line will ring before the system
answers a call. Set for 2, 4 or Toll Saver.
When you set the system for Toll Saver, it
answers after four rings when you have no
new messages, and after two rings when
you have new messages.
1. Press and hold "set up" for about two
seconds. The system announces the
current ring selection.
2 Press and release "ANNC/SKIP" or "MEMO/REPEAT"
until the system announces your ring
selection.
3 Press and release "Play/Stop" to exit

This is the info from the users manual, it seems a bit strange,
but claims if you set the number of rings before it answers, (for the answering system) to "2" it will stop the audible caller ID.
Here it is from the manual.

If you turn on the answering system
and set the number of rings “2” (page
38), the unit does not announce the
caller information. If “Toll saver” is
selected and there is a new message,
the unit does not announce the caller
information.
When you receive a call while on the
phone, the 2nd caller’s name is not
announced even if you subscribe to
both Caller ID and Call Waiting with
Caller ID services

SETTING THE RINGS TO ANSWER
This setting allows you to select the number of rings before the answering system answers a call.

At idle status, hold down the volume "UP" button over two seconds to enter the ring times setting of answering. The answering system announces, "ring time two" (the default is 2).

To change the rings to answer, press and release the "PREVIOUS" button (<<) or the "NEXT" button (>>) and the answering system announces a number such as "2, 1, toll save, 9...” OR "2, 3, 4...", if you select the toll save and the digit LED light shows a “γ”, the answering system announces “toll save”.

After choosing a number, press the “PLAY/STOP” button one time to store the rings to answer, and the answering system confirms the setting and returns to the idle status.

NOTE: when the machine fails to operate properly, just unplug the power for 10 seconds, and redo the settings.