How to Remove/install new screen ,pillips 55 in ,4k ultraHD T.V

Kids eh... who needs em..nothing but trouble. Anyway it's stuffed. It'll cost more to try and fix than to git a new one so sell the kid git a new telly and no more problems.

it has been a while since I worked on one of these but if I remember there are 5 screws to remove 3 on door opening on front and two that r on back side of screen holder that have to be removed then u can take the whole thing out to put new flapper in.

There is nothing more frustrating than a broken laptop screen. Whether you have dropped your laptop or stepped on it,once the screen is cracked it has to be replaced. Having the screen repaired may cost you almost as much as a new laptop. Purchasing a new screen from the manufacturer can also be expensive. Taking the time to look online at computer message boards or resellers can help you to find a reasonably priced screen. By following a few easy steps, you can replace your cracked screen and have a functioning laptop in an afternoon.

Determine what model laptop screen will fit your laptop. Ordering a screen directly from the manufacturer can be almost as expensive as buying a new laptop. Look at online computer message boards, auction sites and retailers to find less expensive options. Disconnect any power source, including the battery pack, from your laptop before you begin. Locate and remove the four to six screws that hold the bezel, or plastic frame cover, in place. The screws sometimes have small plastic or rubber covers over them. Pull the plastic bezel away from the screen cautiously, working around the edge. Some bezels snap in and out of place. A small flat-head screwdriver may be helpful in prying the edge of the bezel away from the screen. Pull the screen forward gently. You will find two main wires behind it. The ribbon-like wire, or video cable, is usually taped in place. Remove the tape and disconnect the video cable from your broken screen. Remove the broken screen from its metal frame. Connect the new screen to the video cable and pop it into the metal frame. Replace the tape, plastic frame and screws. Power up your computer and test your new screen. Hope this helps.
b>

Assuming the screen is physically cracked, you need to obtain a new screen, remove the screen bezel by popping off the rubber caps and undoing the screws under them. The screen is fixed into position by two rails with small screws holding it into place. Remove these and the screen will be freed.
Disconnect the VGA cable and the smaller two wire plug that connects the inverter to the screen, replace the new screen and re assemble

I found some interesting information about your camera. It turns out that the camcorder will only charge its battery if it detects the physical presence of its rechargeable battery pack. Battery detection depends on two physical components. One is a switch located at the top of the battery compartment, The other is a little plastic tab included with the battery pack

Instructions for the fix are located at this link: Fixing Flip UltraHD that won charge its battery

You don't need to remove the axle. Remove the rotor or drum. pound out the broken studs with a hammer. Install the new stud into the hole. Use a wheel nut and some washers to pull the new stud into place. They also make a stud installer tool which makes it a little easier.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

i needed a certain diagram also ang just googled serpentine belt diagrams and it took me to a site and iit was free but i didnt save the name try google

A cracked screen will cost you, but maybe not as much as you think. Instead of replacing the whole , you can spend about $300 and replace the screen yourself. All you need is a small screwdriver.

1)Turn off the power to your screen and unplug all cables connected to it.
2)Remove the battery, if one is installed.
3)Locate the covered screws around the cracked screen. Remove the rubber/plastic covers, then unscrew the screws.
4)Gently remove the plastic frame around the cracked screen and set it aside.
5)Disconnect any power cords or cables going into the LCD screen.
6)Remove the cracked screen and slide the new screen into place. Replace any tape or plastic fasteners that hold it in place.
7)Reconnect all internal cords to the screen.
8)Screw in the frame and replace all the screw covers.
9)Reconnect the power supply and all external cables to the LCD screen and switch it on.

Headlights, Removing and Installing

Removing

• Remove front bumper.

• Remove both Torx bolts (T30) -1-.
• Remove interior Torx bolt (T30) using 1/4"-Torx-bit insert and extension.

NOTE: If necessary, use magnet to remove bolt.

• Disconnect multi-function harness connectors for headlights.
• Turn headlights -2- toward center of vehicle and remove from chassis toward front.

Installing
Installation is reverse of removal, noting the following:

• Adjust dimension -a- via plastic bolt at new headlight.

NOTE: Determine dimension -a- at plastic bolt of old headlight, when being replaced

• Engage headlight in area of center of vehicle in guide -2- via pin -1-.
• Always align headlight according to contours of chassis (gap dimensions) and secure.
• Adjust headlight after installing.

Tightening torque

Component Nm Headlights to lock carrier 6


Repair Kit For Headlight Housing, Installing

NOTE:

• Headlight mounting tabs that have broken off can be replaced by installing the repair kit. Complete replacement of the headlight is therefore not necessary.
• Different repair sets are available for the left and the right headlight.
• Remove headlight with broken mounting tab.
  • Remove remains of the broken mounting tab -1- at location marked with the arrow.
  • Place mounting tab -2- of repair set onto the edge (arrow) of the headlight housing and secure the tab with two screws -3- from rear.

I DON'T KNOW IF YOU CAN FINE DIRECTIONS ITS NOT HARD YOU HAVE TO TAKE ALL THE PLASTIC OFF THAT SURRONDS IT THAT TAKES A PILLIPS HEAD THE HARD PART IS WHEN TOU GET IN SIDE THERE IS A BOLT THAT HOLD IT IN PLACE AND IT IS HARD TO GET OUT THERE IS NO TOOL MADE TO GET IT OUT YOU HAVE TO FINE YOUR OWN WAY BUT IT NOT ALL THAT HARD JUNK YARD GET THEM OUT EVERY DAY