Assembly manual for Tagies peaceful snuggles leafscape swing & sway

https://www.youtube.com/watch?v=s6OqiT0FRBc

I have never heard of a dis-assembly instruction sheet, however, when you buy one, there is an assembly sheet, if it is not assembled already.
A mechanic-type person should be able to figure this out for you.
God bless your efforts.

Could this be what you are asking?
Convert Baby Swing from Batteries to AC wall Power

could be a small bit of dirt on the inside of the volume switch,
try spraying w.d40. then just keeping turning it up and down to see if it clears it.if it crackles as you turn it up or down then its just a bit of dust on the switch.

Take it back they will replace it for you for up to 2 years.

If you look there is a whole in the mobile that the screw driver will go in and take the screw out

YOU NEED THE MODEL NUMBER then follow link below

LOOK FOR THE MODEL NUMBER

• BOUNCER On the back of the vibration unit, below the battery compartment door
• OPENTOP™ SWING Inside the battery compartment behind the batteries
• WIND-UP SWING On the underside of the top housing- the piece of plastic that runs across the top of the swing and is right above the baby's head
• TRADITIONAL SWING Under swing tray
• TRAVEL LITE™ SWING On the bottom of the contoured plastic seat
• SWEETPEACE™ NEWBORN SOOTHING CENTER On the bottom of the seat
• DUETSOOTHE™ SWING + ROCKER On the underside of the housing
• DUETCONNECT™ SWING + BOUNCER On the underside of the housing
• DUETCONNECT™ DLX SWING + BOUNCER On arm with motor hub
• LITTLE LOUNGER™ Inside leg near Rock Lock
• DUET ROCKER™ Backside of front plastic panel with Graco Logo
• GLIDING SWINGS Under motor housing unit (electronics hub on right hand side of swing)
• SIMPLE SWAY™ INFANT SWING On tubing on bottom of unit
• COZY DUET™ SWING + ROCKER Under battery hub on back of swing
• DREAMGLIDER™ GLIDING SWING + SLEEPER On side hub with electronics

Product Instructions Search Results

This could be the problem / answer.

Re: 3500 giving 59.99 error *SOLVED!* by alkemyst (4/10/08 8:16 AM) reply + / - I was reading about the error and another user had an issue with the swing guide plastic falling into the pickup assembly...the swing arm on this printer has in similar shape with the plastic being brittle (I had to use new larger self-tapping screws to fix it properly).

I did this this morning, it only took about 20 mins and was my first time doing this beyond the swingarm guide and removing the Image Drive assembly which gave me some practice :). It's really an easy job IMHO if you have the HP manual downloaded.

Took off the right cover, the right swing arm, left swing arm (probably not needed), the swing rod guide, the unclipped the harnesses on the pick up/feed assembly as well as unloomed the harness and the 5 screws that hold it. Then two more on the solenoid behind it and a cable or two...then that gear that was right off the solenoid had a visible offending piece of plastic, this step is page 224 in the repair manual, steps 16-19 ish, the double gear assembly that is there when you remove the pickup solenoid had the sliver of plastic from the swing arm assembly between the two gears.

Prints great again. The swing arm assembly seems to be falling apart on alot of these...may explain the large amount of 59.99 errors being reported lately.

I received a Sweet-peace newborn swing and the A/C plug is pushed in. Is there a way to retrieve it? How hard will it be to take the swing apart and retrieve the plug? You can reach me at my e-mail at: [email protected] Thank you for your time.

I found one online: http://media.gracobaby.eu/manuals/Sweetpeace%20UK.pdf